What is Needed to Install Curt Trailer Hitch, # C11496 , on 2009 Honda Accord Sedan

Question

Question:

Hi. I want to install a hitch on my accord to pull a 4x6 utility trailer. I will be transporting two dirt bikes with it. The bikes weigh 190 lbs each. What do I need? From hitch to tongue to ball? Thanks in advance.

asked by: ron v

0

Expert Reply:

On your 2009 Honda Accord 4 door sedan the Curt Trailer Hitch for the 2009 Honda Accord, # C11496, will work fine. It has a Gross Towing Weight Capacity of 2,000 lbs. So if your bikes and total contents that will be on the trailer is under that, you would be fine. It bolts on and comes with detailed instructions. I will send a link with the installation instructions.

Also needed is a Draw-Tite Ball Mount, # 3593, and it includes the pin and clip. On the hitch ball you might want to check the coupler on the trailer and see if you need a 2 inch or 1-7/8 inch ball. If it is 2 inch ball you need a Tow Ready Hitch Ball with 2 inch Diameter and Short Shank, 3,500 lbs GTW, # 19258. If it is a 1-7/8 inch ball you need a Tow Ready Hitch Ball with 1-7/8 inch Diameter and Short Shank, 2000 lbs GTW - Chrome, # 19256.

The wiring harness needed is Tow Ready T-One Vehicle Wiring Harness, # 118420, which is a easy installation, no cutting or splicing is needed. The connection plugs into the tailights and the trailer connector is stored in the cargo area when not in use. I will send a video link to a wiring harness installation similar to your vehicle.

expert reply by: Jeff D

0

Answer 1

The Kuat Sherpa 2.0 #SH22G and the NV 2.0 #NV22G that you referenced are both excellent platform-style racks that will hold your bikes by the front wheels with no frame contact. These are top-of-the-line carriers and you really would not go wrong…

view full answer...

Answer 2

In order to satisfy Curt warranty requirements, any of their Class I or II receivers (like the C11423 you referenced) as well as a few of their Class III hitches must be used with a stabilizing strap like part #18050. This applies to any…

view full answer...

Answer 3

Both Curt trailer hitch receivers that fit your 2009 Honda Accord, parts #C11496 and #C11085, are Class I hitches that measure 1-1/4 inches. They also have the same towing and tongue weight capacities. They even install in the same location and…

view full answer...

Answer 4

I recommend the Curt Trailer Hitch Receiver #C11496 as being the best receiver for your 2009 Honda Accord. The cross tube has plates on both the bottom and top of the receiver to give it additional strength where others only have a plate on one side.…

view full answer...

Answer 5

The ground clearance you would have on your 2008 Honda Accord would be right at the same amount that you currently have as the hitch will hang right at the same height as your 2008 Honda Accord. I attached a couple pictures that show the relative…

view full answer...

Answer 6

The hitch you were looking at, part #C11496, is not really visible unless you are about eye level with the hitch. The cross bars are swept back to tuck them underneath the vehicle. I have included a link to the instructions that will show you the…

view full answer...

Answer 7

As a large portion of the hitch will be visible below the rear bumper fascia, I would recommend the Curt Class I Receiver hitch, part #C11496. The hitch crossbar is constructed of round tubular steel, instead of the square tube like the other…

view full answer...

Answer 8

We don't have that specific style of hitch for your 2009 Honda Accord but we do have the Curt hitch part #C11496 which fits the sedans and coupes which has the much more popular 1-1/4 inch square hitch opening. This size of hitch would be much…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

What is Needed to Install Curt Trailer Hitch, # C11496 , on 2009 Honda Accord Sedan

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching