How to Determine what Replacement Hub and Bearing Kit

Question

Question:

What is agricultural spindle? I cannot find a hub for my spindle size and wonder if that may be the problem. My spindle size is 1inch x 3.25. It is a homemade trailer.

asked by: Bob

0

Expert Reply:

Thanks for sending a couple pictures! An agricultural spindle is mainly used in agricultural settings and best at low speeds.

The best way to determine the correct parts for your homemade trailer, is to remove the hub from the trailer and either get part numbers from the inner and outer bearings and races, and grease seal or measure the spindle in 3 places and the hub in two places.

I have included a photo showing the places to look for part numbers and places to measure. If the part numbers are not visible on your bearings, races and seal a dial or digital caliper will be needed to get accurate measurements. Using a tape measure or ruler will not be accurate enough.

I am including links to a FAQ page and a video that will help you when replacing the bearings, races, and seals on your trailer.

If you wish to provide your existing bearing, race and seal part numbers, I can double-check to ensure you are getting the correct bearing kit.

expert reply by: Chris B

0

click to enlarge

Answer 1

How deep is it? It is hard to tell from the picture. You may be able to use some emery cloth and take care of it unless it is too deep. Then you would want to go ahead and replace the axle. Even though spindles are available by themselves you would…

view full answer...

Answer 2

It is possible we have the right hub and drum (which I think is what you were referring to by brake drum kit) for your older boat trailer, but more information is needed to determine the right hub for your trailer, which I can help you figure out.…

view full answer...

Answer 3

Replacement of a spindle on a trailer axle is best left to a professional installer. This is not a do-it-yourself type of project. We urge you to use a professional welder experienced in axle fabrication. Proper alignment and welding are critical to…

view full answer...

Answer 4

I would be happy to recommend the parts needed to add electric brakes and new bearings on your 2010 Stehl ST80TD Tow Dolly, but first I will need you to confirm which bearings your spindle uses and if you already have a brake mounting flange…

view full answer...

Answer 5

Bearings fit pretty tight onto spindles. There basically should be no play at all between the inner portion of the bearing and the spindle. They don't fit so tight that they would have to be pressed on, but they sometimes can be tight enough that…

view full answer...

Answer 6

Most campers that long are tandem axles so I would go that route. I took a look at some common GVWR's for campers of that size and it was in the 5,000 lb - 7,000 lb range so you need to keep that in mind; something like the 89" Dexter…

view full answer...

Answer 7

To find the right replacement hub for a trailer you will need the inner and outer bearing numbers stamped into the sides of the bearings or the measurements of the spindle to 3 decimal places. The measurements have to be as accurate as possible so I…

view full answer...

Answer 8

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 9

Yes you can install the Hopkins Insight brake controller in your 2021 Ford Ranger and actually you don't need anything else to do so. Your Ranger doesn't have a connector for brake controller wiring and instead has 4 blunt cut wires that are…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...