Nut Recommendation for the Wet Bolt # 34007-187-00

Question

Question:

Seeing that this is a step bolt what size is the shank and what size are the threads? Your specs says it has 9/16inch threads which cant be right if the shank is going to fit through the hole in a shackle. What nuts do i use with these bolts?

asked by: Adam

1

Helpful Expert Reply:

The nut that is recommended with the # 34007-187-00 is the part # 192600 which is designed for 7/16 inch diameter threads that are 20 threads per inch. The diameter of the rest of the bolt is 9/16 of an inch.

expert reply by: Jameson C

1

Answer 1

On the wet equalizer bolt #126B2 it does not matter which way the hole faces. Up, down, left, right, anywhere in between, it's all good. A lock nut has mismatched threads a little ways along the thread spiral and either its threads, the bolts…

view full answer...

Answer 2

I reached out to the manufacturer and the Wet Equalizer Bolt with Locknut and Grease Zerk for Double-Eye Springs - 3-5/16" Long #126B2 is a pressed in zerk fitting, so it cannot be replaced. This is also true for Dexter bolts as well. There are…

view full answer...

Answer 3

You can definitely use wet bolts with leaf spring trailer suspension. The usable length (distance from back of bolt head to beginning of threads), of the part #126B2 is right at 2-5/16 inches and the overall bolt length (including threads) is 3…

view full answer...

Answer 4

The orientation of the grease hole on the wet bolts of the Dexter Heavy Duty Suspension Upgrade Kit #K71-358-00 does not matter. When you go to install this you don't have to worry about that at all.

view full answer...

Answer 5

The shackle strap length is measured from the center of one bolt hole to the center of the other. The Dexter Heavy Duty Suspension Upgrade Kit for Single Axle Trailers - Double Eye Springs #K71-358-00 uses 3-1/8" long shackles which are found on…

view full answer...

Answer 6

Thank you for providing a photo of your trailer shackle straps showing the extra non-threaded portion of the Redline zerk-fitted bolts #126B2. Shackle bolts are intended to have a fairly loose fit with the shackle straps when installed properly. This…

view full answer...

Answer 7

The part #34007-187-00 is indeed a 9/16-inch diameter wet bolt with a step to a 7/16-inch thread. I pulled one of these from the warehouse so I could measure it for you. The linked image shows the dimensions of each portion of the bolt. They are,…

view full answer...

Answer 8

Redline Step Wet Bolt for 1-3/4" Double Eye Springs #34007-187-00 is fitted with a threaded grease zerk; this is why the zerk fitting has wrench flats. I confirmed with my contact at Redline.

view full answer...

Answer 9

The main difference between the Redline Wet Bolts #126B2 and #34007-187-00 is that the 126B2 has a 9/16" threaded end while the 34007-187-00 has a 9/16" main body but then the threaded portion reduces to 7/16" so they use different…

view full answer...

Answer 10

The Road Armor Shock Absorbing Equalizer Kit #LC696740 that you referenced can fit standard trailer suspension hangers. You do not need special hangers to use this kit.

view full answer...

Answer 11

To determine if the Road Armor Shock Absorbing Equalizer Kit #LC696740 will work on your 2007 Coachmen Travel Trailer you will need to take a couple measurements on your existing equalizers. These upgraded units have a width of 6 inches from hole to…

view full answer...

Answer 12

The Road Armor equalizers, part #LC696740, are 3-1/4 inches tall from the center of the top bolt hole to the line where the center of the lower bolt holes straight down. They're shorter than your 13-10 equalizers but they're the closest…

view full answer...

Nut Recommendation for the Wet Bolt # 34007-187-00

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching