What Hardware is Included With the Curt Class III 2 Inch Hitch # 13591

Question

Question:

Hi, I dont see what items comes with the hitch? Bolt? Bolt wire to fish the bolt? etc. Thanks

asked by: Roberto C

0

Expert Reply:

Our hitches ship with the all the installation hardware needed including bolts, nuts, washers, and fish wires if needed. Many of our hitch descriptions have pictures of this, but some do not. If you want to see the parts included, you can check the instructions for the hitch linked on the product page. I have added a link to the instructions below.

The Curt Class III 2 Inch Hitch, # 13591, for your 2007 Saturn Vue includes 6 hex head bolts, 2 carriage bolts, 2 spacers, 6 conical tooth washers, 2 hex nuts and 1 fish wire.

expert reply by: Patrick B

0

Answer 1

Dirty and rusted weld nuts are actually not too uncommon, in fact we have a dedicated article on exactly this subject that I have attached. You will want start by cleaning them out with a spray lubricant (WD-40, etc) and a simple wire brush. You may…

view full answer...

Answer 2

The Curt hitch part #C13195 that is a confirmed fit for your 2017 Kia Sorento has a list of tools needed to install the hitch in the attached installation instructions link. I attached a picture that shows this as well as the install time. Basically…

view full answer...

Answer 3

The etrailer Trailer Hitch Receiver #e98865 that you referenced is confirmed to fit your 2014 Chevy Equinox. What you are experiencing is not too uncommon and it sounds like you may have already looked into the cause. On vehicles that have seen a few…

view full answer...

Answer 4

All of the trailer hitches we carry for your 2018 Kia Sorento include the necessary bolts and hardware for installation. The Curt Class III Trailer Hitch #C13195 that you were looking at mounts to your Sorento using the included (2) 1/2-13 x 4-1/2…

view full answer...

Answer 5

Yes, there is some rear fascia trimming needed to install the etrailer Hitch part #e98865 on your 2016 Chevy Equinox. I attached an install video that shows the trimming that you need to do.

view full answer...

Answer 6

For your 2019 Hyundai Santa Fe I recommend the Curt Class III Round Tube Receiver Hitch #C13195. This Class III hitch is confirmed to fit your Santa Fe and it will use existing holes in the vehicle's frame for a no-drill installation. It will…

view full answer...

Answer 7

The etrailer brand #e98865 hitch has a 350 lb tongue weight capacity, which means that the maximum amount of downward force that a hitch mounted accessory can safely place on the hitch is 350 lbs. I'm not sure what your ramp consists of, or…

view full answer...

Answer 8

The first thing you will want to check is the owners manual for your 2015 Chevy Equinox. The manual contains the manufacturers recommendations and procedures for towing. Often times they recommend a break-in period on new vehicles before you can tow.…

view full answer...

Answer 9

Even when a hitch is installed properly we sometimes run into an issue of the exhaust coming into contact with the trailer hitch so we put together an article which provides a few different solutions. I have attached this article for you.

view full answer...

Answer 10

The M12 size is correct for installing a hitch like the etrailer.com #e98865 on your 2015 Chevy Equinox. We had the chance to install this hitch on a 2015 model just like yours and the hardware was the correct size. See attached video link. There…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...