Grease Seal Recommendation for a Trailer Spindle with 1.5 in Inner Diameter
Question:
I have a few customers with this setup and think that a bearing buddy seal would be a cost effective way to repair these trailers. The bearings are l44649. The outside diameter of the seal is 1.98 and the inside of the seal is 1.5. I do not see any kits available with these specs. The bb60005 kit lists the l44649 bearing and a od of 1.98 on the seal but the id is too small. Is there a kit available for a 1.0625 axle and a 1.5 id seal? Elsewhere on your site someone suggested that the bb60005 does have a 1.5 id but i do not see that in the spec sheet.
asked by: Steve R
Expert Reply:
If your customers are blowing out their grease seals most likely that is due to too much grease being pushed into the hub. Using a Bearing Buddy Seal like the part # BB60005 would give you a grease seal that is more reinforced than a standard one, but a regular seal would also work just fine.
The # BB60005 has an inner diameter of 1.375 inches and an outer diameter of 1.980. Since you are looking for a seal that has an inner diameter of 1.5 in you would want the part # 10-9 if the outer diameter you need is 1.987 or # SL150 if the OD you are looking for is 2.332 in.
Products Referenced in This Question
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.500 Inch I.D.
- 1.987 Inch O.D
- TruRyde
more information >
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Single Lip
- 1.500 Inch I.D.
- 2.332 Inch O.D.
- Redline
more information >
Product Page this Question was Asked From
Spindle Grease Seal Set for L44649 Inner Bearing and 1.980 Bearing Buddy
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.375 Inch I.D.
- 1.98 Inch O.D.
- Bearing Buddy
more information >
Continue Researching
- Search Results: hydraulic hitch
- Search Results: 84 spindle
- Search Results: 84546uc3
- Shop: Spindle Grease Seal Set for LM67048 Inner Bearing and 1.781 Bearing Buddy
- Shop: Spindle Grease Seal Set for L68149 Inner Bearing and 1.810 Bearing Buddy
- Shop: Dexter Nev-R-Adjust Electric Trailer Brake Assembly - 10" - Right Hand - 3,500 lbs
- Shop: Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2
- Search Results: grease seal 10 19
- Search Results: 10 19 seal
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles
- Shop: Demco Hydraulic Brake Actuator - Drum - Primed - A-Frame - 2" Bulldog Coupler - 7,000 lbs
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: bearing buddy
- Article: Most Popular Wheel Bearings
- Shop: Trailer Hitch
- Search Results: 25580
- Q&A: How to Tell if Trailer has a BT8 or BTR Spindle Installed
- Shop: Trailer Wiring
- Article: Trailer Wiring Diagrams
- Shop: Brake Controller
- Article: Trailer Tire Sizing
- Q&A: How to Determine the Size of a Trailer Hub Assembly for Replacement
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Video: etrailer Electric Trailer Brake Kit Installation
- Q&A: How to Measure to Determine the Size Trailer Brakes Needed For Hydraulic Drum Replacement
- Shop: Suspension Enhancement
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: What is the Best Grease for Trailer Bearings
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub