Do you Carry Hidden Hitch Mounting Bracket for a Round Tube Hitch

Question

Question:

I need a mounting box for a 7-way round connector. This box will be mounted to a ROUND tube Hidden Hitch. On your website, I clicked on the mounting box category and it contained no items. Do you have a mounting box for this type of hitch? On the HIdden Hitch website, the part number is 118159.

asked by: Todd

0

Expert Reply:

We carry the same part, but the part number is a bit different. The 6 and 7-Way Trailer Connector Mounting Box for Round Tube Hitches is listed on our website as part # 18159.

expert reply by: Sarah

0

Answer 1

We have just what you are looking for. The mounting bracket I recommend is part #18140. This uses a hose clamp that is placed around your trailer hitch so you do not have to do any drilling.

view full answer...

Answer 2

Yes, when installing the knob for the Redarc Tow-Pro Liberty Brake Controller item #RED24FR you will want to remove any extra material behind the insert. I am happy the video was able to help you out. I have linked a couple of pictures from the…

view full answer...

Answer 3

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 4

The replacement rubber caps on the Malone SteelTop Roof Rack #MPG202 can be found as part #MAL53TR. This comes as a set of 4 so you can have some others on hand if the need arises.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Do you Carry Hidden Hitch Mounting Bracket for a Round Tube Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching