What is Lowest Height Setting of Curt A20 5th Wheel Hitch When Used as Slider

Question

Question:

Curt A20 is adjustable 17.5-21.5. What is the lowest height possible when used as a slider? What are the adjustment increments? Thanks

asked by: Lloyd P

0

Expert Reply:

I spoke with my contact at Curt and he said the lowest height possible of the Curt A20 5th Wheel Hitch, # C16541, when used as a slider is 17-1/2 inches, and that the adjustment increments are 2 inches.

expert reply by: Chris O

0

Answer 1

Yes, you can use the Redarc 200 watt solar panel with your RV that is pre-wired for solar, but you would not be able to use just the Solar Panel #RED86VR. Solar panels require a charge controller to regulate the battery charge so you would need to…

view full answer...

Answer 2

Curt and B and W make excellent fifth wheel hitches. Since Lippert made your Flexair pin box and they recommended a Curt over a Companion I would make the same recommendation. My favorite Curt fifth wheel hitch is the #C16541 which would work well…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 7

Hey Mark, since we know your Brinkley Z3100 has the Rhino style pin box, the correct Gen-Y fifth wheel to gooseneck adapter is the part #GY98GR which comes with the auto latch you mentioned wanting as well!

view full answer...

Answer 8

You can replace the Lippert Rhino pin box on your Brinkley 5th wheel. The right one though is going to depend on the pin weight of your trailer. Here are the options that will work to replace the Lippert Rhino: - Pin Weight of 1,500 lbs - 3,500 lbs:…

view full answer...

Answer 9

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 10

While it is recommended to use a sliding 5th wheel for a short bed truck so that you have plenty of clearance for sharp turns, it is not necessarily required as it depends on your truck and trailer configuration. If you are using the same trailer…

view full answer...

Answer 11

The Ford OEM puck system is different than the Chevrolet/GMC OEM puck system therefore, you can't use a 5th wheel hitch from one in the other. The Ford OEM system has pucks which are much closer together than on the Chevrolet/GMC OEM system. The…

view full answer...

Answer 12

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...