What is the Right Replacement Bulb for Optronics RV Scare Light

Question

Question:

Can you give me the led bulb # to fit the rvsl31 scare light ?

asked by: Keith N

0

Expert Reply:

The RV Scare Light, RVSL31, uses an 1156 bulb. A white LED 1156 like # DI85VR would fit the socket. This light has not been tested with LED bulbs though so I cannot guarantee that it will work.

expert reply by: Michael H

0

Answer 1

I measured the Replacement Blades for AirrForce 42" Hugger Style RV Ceiling Fan #277-000398 for you and they are 16- 5/8 inches long with 4 inches wide at the bottom and 4-7/8 inches wide at the top. I've attached a photo to assist.

view full answer...

Answer 2

The Replacement Fan Blades #277-000398 are 16-5/8-inches long. They measure 4-7/8-inches wide at their widest point and 4-inches wide at their narrowest point. These install onto brackets like #277-000399 which then attach to the fan itself.

view full answer...

Answer 3

According to the manufacturer the #277-000399 replacement brackets will probably work for a AirrForce 42" hugger-style 4-blade ceiling fan without a light. They said they believe the same brackets are used for both. Since there is some…

view full answer...

Answer 4

The holes that mount to the motor for the Replacement Brushed Chrome Brackets for AirrForce RV Ceiling Fan with Light #277-000399 do measure 1-1/2" on center just like what you have. I have attached a photo that has additional measurements…

view full answer...

Answer 5

Based on what you are saying, it sounds like the detector is faulty and needs to be replaced; you did the right thing with vacuuming it and checking the batteries, as those are the two steps that need to be taken to ensure there isn't a…

view full answer...

Answer 6

Yes, the Lippert Components Heavy Duty Landing Gear Motor part #LC196308 would be a more dependable option than the Lippert Components High Speed Landing Gear Motor part #LC141893 that you have now. This motor has a higher weight capacity (6,500…

view full answer...

Answer 7

Trailer makers don't keeps specs on items like lights but if you can get a look at the light's base that is where you will usually find a part number and perhaps a brand name for the whole light. You may need to remove the base from the…

view full answer...

Answer 8

The lens on the RV Oval Porch and Utility Light #RVPL7C is held to the housing with some tabs on the lens that fit slots on the housing. To remove the lens you will need something thin and flat like a knife or small screwdriver to gently pry the lens…

view full answer...

Answer 9

We do have some motion activated porch lights but part #RVSL31 from Optronics is not one of them. I've linked our complete selection for you. I personally own and use part #DG0132 at my house and it's doing great. It stays on a dim mode all…

view full answer...

Answer 10

You will need to either put some upwards or downwards pressure on the lens and then rotate it outwards to gain access to the inside of the RV Porch Utility Light w/ Switch #RVPL7C for changing the light bulb, mounting it, or replacing the Clear Lens…

view full answer...

Answer 11

The Create-A-Breeze roof vent is a Fan-Tastic Vent Roof Vent Fans and from your description you have a model 8000 vent. The correct replacement is the Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans #FVK8017-00. I have added a…

view full answer...

Answer 12

Yes, the Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans part #FVK8017-00 is the correct replacement fan/motor for your Fan-Tastic Vent Create-A-Breeze Model 8000.

view full answer...

What is the Right Replacement Bulb for Optronics RV Scare Light

Product Page this Question was Asked From

Continue Researching