How to Ground the Teardrop Clearance Lights CB-15AK

Question

Question:

I just installed these running lights directly to fiberglass. But the lights do not illuminate? Do these lights have to be mounted directly to metal for proper grounding? Thanks

asked by: Ron C

0

Expert Reply:

The lights in the teardrop light kit # CB-15AK ground through the mounting hardware so you would need to either attach them to metal or have the mounting hardware go through a ring terminal on the end of a wire and attach the other end of the wire to a bare metal surface.

expert reply by: Michael H

0

Answer 1

Yes, you can replace the incandescent bulb inside of the Optronics Clearance or Side Marker Light part #CB11WAB with an LED. That said, it must be a #67 bulb type and the color of the light must be the same as that of the lens. We do not carry this…

view full answer...

Answer 2

The lights in the teardrop light kit #CB-15AK ground through the mounting hardware so you would need to either attach them to metal or have the mounting hardware go through a ring terminal on the end of a wire and attach the other end of the wire…

view full answer...

Answer 3

The Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets #RM47MR typically comes centered and you would only need to make adjustments after installation and testing to see if it continues to pull. If you adjusted it all the way out to where…

view full answer...

Answer 4

Roadmasters priority when it comes to their sway bars is top notch quality and the easiest install for the customer. This typically cuts the install time down enough that you end up saving money if you pay to have the bars installed or decide to do…

view full answer...

Answer 5

The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a 1…

view full answer...

Answer 6

In regards to the Roadmaster Exact Center Steering Stabilizer part #RM47MR, the stabilizer installs on the front of the steering arm pointed down. I have attached a photo of this below. If this wasn't what you were looking for, please just let me…

view full answer...

Answer 7

There is a suspension enhancement option for your 2021 Entegra Vision XL built on a Ford F-53 chassis, but I verified with the manufacturer that the steering stabilizer only fits if you have at least a 24,000 lb GVWR. You're not out of luck…

view full answer...

Answer 8

I found the online version of the install instructions for the Exact Center stabilizers like the #RM47MR. What's fun is that just when you think you have found the correct step to address your problem it tells you to continue to the next step.…

view full answer...

Answer 9

To flat tow your 2021 Jeep Wrangler Unlimited 4Xe Rubicon Hybrid you will need a tow bar, base plate, tow bar wiring kit, braking system, and safety cables. I have the following recommendations for you listed below: Tow Bar: Roadmaster Nighthawk All…

view full answer...

Answer 10

For your 2024 Ford F-53, I recommend checking out the Timbren Front Suspension Enhancement System #TFFF53B for the front, and the Timbren Rear Suspension Enhancement System #TFRF53A for the rear. These kits do not require drilling, will replace your…

view full answer...

Answer 11

To replace/upgrade the bushings on the rear factory sway bar of your 2009 Class A Newmar Canyon Star RV you need one of the following Roadmaster kits based on the diameter of your factory sway bar: - 1-3/8" Diameter #RM-4139-300 - 1-1/2"…

view full answer...

Answer 12

I did some looking and found that the 46210 and 46845 hubs you currently have use the same #L68149 inner bearing and #L44649 outer bearing. However, as we do not carry the Tie Down Engineering Vortex hubs, I cannot say what all will fit them,…

view full answer...

How to Ground the Teardrop Clearance Lights CB-15AK

Product Page this Question was Asked From

Continue Researching