Where Does the Black Wire Attach for Harness 30717 on a 2003 Chrysler Town and Country

Question

Question:

I understand the black is the hot wire goes to the 12V. Where on the vehicle should you splice into 12V. I have a 2003 Chrysler T&C. Thanks

asked by: Don

0

Expert Reply:

The black 12 volt lead on Adapter 4 Pole to 7 Pole Vehicle End Trailer Connector, # 30717, attaches directly to the battery on your 2003 Chrysler Town and Country.

You will have to attach the black wire to a length of additional wire, like 10 Gauge Blue Primary Wire - per foot, # 10-1-1, under your vehicle and run that wire to the battery through a 40 amp circuit breaker, # PK54540.

expert reply by: Michael H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

For your 2024 Hyunda Santa Cruz we have the Curt 7-way kit part #C68JR that is a confirmed fit. This installs by plugging into a factory wiring connector on your vehicle which means a really easy install that doesn't require any splicing.

view full answer...

Answer 6

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 7

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 8

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 9

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...

Answer 10

The best brake controller for your 2024 Toyota Grand Highlander is from Redarc, and the correct part number for it and the needed wiring adapter is the following: - Redarc Tow-Pro Liberty Trailer Brake Controller #RED24FR - Wiring Adapter for Tow-Pro…

view full answer...

Answer 11

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...