What are the Wire Gauges Used in Pollak 5th Wheel / Gooseneck T-Connector # PK11893-11932

Question

Question:

wire size of hot

asked by: Jim L

0

Expert Reply:

The 12 volt power wire in the Pollak 5th Wheel / Gooseneck T-Connector # PK11893-11932 is 10 gauge. The ground is 8 gauge. The Brake output wire is 10 gauge. All others are 12 gauge.

expert reply by: Michael H

0

Answer 1

I have the perfect option for your 2019 GMC Sierra 2500 that will not require you to use an extension harness in order to connect the lighting on your gooseneck trailer. For this, I recommend the 5th Wheel/Gooseneck 90-Degree Wiring Harness part…

view full answer...

Answer 2

The black wire of the #PK11893-11932 does carry the 12 volt power circuit. This circuit is a 12 gauge wire. The standard amperage rating for 12 gauge wire is 41 amps typically, but this harness has a 30 amp rating. I attached a diagram that has a…

view full answer...

Answer 3

I attached a picture that shows the pin out diagram for the Pollak 5th Wheel / Gooseneck T-Connector with 7-Pole #PK11893-11932 that you referenced.

view full answer...

Answer 4

The 5th Wheel/Gooseneck T-Connector harness you were looking at will only fit Ford/GM/Nissan and newer Dodge style connectors. If your 2007 Dodge Ram 3500 came with a factory 7-Way, you will need Draw-Tite part #20111. Remember to use a bit of…

view full answer...

Answer 5

How is the 7-way in your truck bed installed? Is it a T-connection like the #PK11893-11932 you referenced? If so, unplug the fifth wheel connector portion of it entirely and plug the factory US car connector into the rear of the 7-way on the rear…

view full answer...

Answer 6

I looked through the owner's manual as well as some wiring schematic for your 2016 Ford F-53 chassis and there is no mention of a 12 volt trailer tow battery feed. After some additional research online it seems as if this circuit was excluded…

view full answer...

Answer 7

On GM vehicles of that vintage, the 12-V pin should be hot regardless of whether the ignition is on or not. If it isn't showing voltage even with the ignition on, you're almost certainly on the right track thinking it's a blown or…

view full answer...

Answer 8

In order to add the battery charge line circuit on a 7-way trailer connector you can use the Roadmaster Battery Charge Line Kit part #RM-156-75 which comes with everything you need and most likely more wire than you'll actually need. In regards…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

What are the Wire Gauges Used in Pollak 5th Wheel / Gooseneck T-Connector # PK11893-11932

Product Page this Question was Asked From

Continue Researching