Summer Starts Here - Save up to 70%
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring - no cutting, splicing or tapping required. Converter is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side tail lights. You will have to remove the tail light assemblies and interior trim panels to access this harness.
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of the trailer. This converter combines the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
California residents: click here
Average Customer Rating: 4.9 out of 5 stars (20 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring - no cutting, splicing or tapping required. Converter is made using SMT to ensure superior performance.Product is very good and fit well Paper instructions for a little confusing video help quite a bit
The product installed easily, and exactly like the instructions said. The only complaint I have is with the design. So you run the pigtail out the back hatch of the Pacifica. Which is okay, but it seems like with a bit more wire you'd be able to route it down through the tail light assembly on the drivers side and then along the hitch itself.
I'm afraid the door closing on it over and over again is going to sever the wires.
Hardest part was taking out the torks bolt for the belt re-tractor on the driver side.
Lee
11/29/2019
No problems at all and use it every few weeks.
I can't say enough great things about etrailer. Even through email, responses are very quick. They were able to help me get the right part when part of my order was wrong through no fault of their own. I could not ask for better customer service. Thanks, etrailer!
It all shipped safe and sound. I was able to easily install. Thanks for the online videos.
Fast delivery and super easy to install all a matter of about 30 minutes from start to complete and I am very picky on how things are done.
Got it fast and it was easy to get the correct parts and was delivered very fast .well done
Carl L.
8/16/2019
The kit was awesome. Exact fit and easy easy to install. And is working perfectly. And the plug in that comes with it that tells you all is working correctly Very nice
I could not be happier with what I received. Install was a breeze and look to use etrailer for all my trailer needs!!!
Easy to do install
My package arrived swiftly in the mail and was well packaged. Great service support on a returned item also. Thanks.
no problem some far
Excellent, just what I was needing, and in 4 days. Others were saying 2-5 WEEKS!!
Very nice product and fast shipping
Perfect fit . So easy
Was install
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Bob P.
10/15/2022
Working great. not bad installing it either. I would recommend this product rather than try to wire it any other way.