To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. Connector plugs directly into existing wiring - no cutting, splicing or tapping required. Converter is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's wiring harness, which is located either behind the driver's-side access panel in your rear cargo area or beneath the floor of your cargo area.
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plug on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of the trailer. This converter combines the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
California residents: click here
Average Customer Rating: 4.9 out of 5 stars (30 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. Connector plugs directly into existing wiring - no cutting, splicing or tapping required. Converter is made using SMT to ensure superior performance.All good worked as it should.
I was trying to order tailer wiring for a 1983 Camaro what I got/ordered was for a Chevy tracker, or three Suzuki models. The one pictured on your website showed a wiring diagram printed on the product case which does not exist on the unit delivered.
Snapped right on wasn't sure what to do with what I guessed was the ground wire...
Called the help line... on hold for 2.5 Beetle's songs... and they confirmed my guess and suggested ways to secure it to frame
Very easy to install and it is a very well made product.
Easy and accurate ordering process, with fast shipping. None of the pictures or details fit where the wiring harness connection location was on my 03 Tracker. My harness connection was taped down about 2' toward the front from the Jack storage compartment. Snap-out removal of the top of the side panel from rear to back seat was required. Once you removed the tape holding the harness connection it would barely reach the Jack storage compartment.
Bryan S.
11/3/2018
Works fine, install more difficult for my model, I guess.
Once I found the vehicle wiring, just plugged in and everything worked.
The connector is behind the side panel in the luggage compartment so you have to partially remove the side panel to expose the plug.
Mojo
8/10/2015
Still working great
I bought this trailer from HD it was all wired but not my Suzuki Grand Vitara , I looked all over town for a wiring harness , nothing then looked on the internet , found etrailer.com looked like the best one for my car and the price was right , so I ordered it and it turned out to be the best choice , it worked perfect and easy to hook up , hard to believe how good everything worked out . Thanks , Ray
My wiring harness plug was "hidden" behind the driver's side rear wheel panel. I had to pull the panel out from the top and finesse the tape off and the plug free and back. I didn't secure the "black box", just stuffed it in the jack compartment. The connection pigtail passes out under the taillight and under the body perfectly to the hitch.
I used this factory plug in pigtail to replace a "splice job" on the tail lights. Reasonably quick, simple, easy no fuss, and it works.
Easy way to hook up trailer wiring. I removed tail light to route wire under and along frame. Had cut notch in bottom of gasket and plastic bottom of tail light housing. Sealed with dab of silicone.
took 5 min. to put on car
it was super easy to install and I use it all the time. I even got it to power my backup cam.
Only took a couple days to get this hitch and wiring harness mailed to my house, very happy with that
Easy to install. Five minutes max. Most of that time taking jack out and putting it back. Unit just plugs in to connector and your done. Thanks
The install was simple and easy. It only took 5 minutes and I took my time. Just tap in the ground with the provided self tapper then hook up to the trailer and go.
Great instructions helped to install this well constructed product easily.
easy straight forward installation, fit perfectly
great product, good service. Prompt delivery. Thank you for a good experience
Re.ggie W.
7/13/2016
works like a charm ,solved my problem
It fit as promised . Looks and fits as promised ! LOOKING forword to useing the product to is full potenual !! Insatallation was strate forward..
Great product and company
Great product and easy to install without having to splice wires
Please see my previous review. Excellen t!
Gteat
Kit is complete and works with no probl ems.
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Katrina B.
4/8/2023
Oh boy, you are right. This harness will not fit your 1983 Camaro. Part # 18252 will fit though! You can get a return and new order set up with our customer service team! Ill send your info over to them!