Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"

See what our Experts say about this Draw-Tite Trailer Hitch

• Trailer Hitch for 2004 Freightliner Sprinter 2500 with Factory Step Bumper
  Yes, we have the Draw Tite hitch part # 75210 as a confirmed fit for your 2004 Freightliner Sprinter 2500 that has the factory step bumper. Draw Tite states that on vehicles with factory step bumper, bumper mounting brackets will be re-attached at original position with fasteners provided with hitch.
  view full answer...
• Will The Draw Tite 75210 Fit Vehicles With The Factory Step Bumper
  I apologize for any confusion. With these 2005 Sprinters there are many different versions, and sometime our vehicle listing can get a little crowded/confusing. The draw tite hitch # 75210 will be a good fit for your 2005 Sprinter 158" wheelbase SRW with the factory step bumper. We have confirmed this with the folks at Draw-tite, as well as with several of our customers, who have successfully installed the hitch on vehicles with the step bumper.
  view full answer...
• Trailer Hitch for 2002 Freightliner Sprinter
  The first generation of the Freightliner Sprinter in the U.S. covered years 1995 through 2006. We do show a hitch fit for the 2003 but not for the 2002, as you noted. It is possible that the Draw-Tite hitch # 75210 will fit but my contact there could not confirm this absolutely since they have not had one in for test fit. We do offer multi-fit RV hitches that feature adjustable brackets. You can see these on the linked page. These frame-mount hitches vary in their tongue weight (TW) and...
  view full answer...
• Exact Measurements for Curt and Draw-Tite Hitch Receivers for a 2005 Dodge Sprinter
  I would be happy to help you. We have those items and I was able to get the measurements for you. I have attached pictures detailing the specific dimensions you have asked for. The Curt Hitch Receiver Item # 13250 fits the 118 inch wheelbase with single rear wheels,140 inch wheelbase with single rear wheels, and 158 inch wheelbase with single rear wheels on 2005 Dodge Sprinters. The Draw-Tite Hitch Receiver item # 75210 fits 2005 Dodge Sprinters with a 140 inch wheelbase with single rear...
  view full answer...
  
• Trailer Hitch for 2006 Dodge Sprinter That Fits Around Spare Tire
  The spare tire retainer would almost certainly interfere with installing the # 75210, but we do have a hitch that is positioned a bit differently so it would fit perfectly. The Curt # 13250 class III hitch will avoid the spare tire retainer, as shown in the provided photo.
  view full answer...
  
• Recommended Trailer Hitch and Towing Setup For 2003 Freightliner Sprinter 2500 158" Wheelbase
  I am not sure why the RV dealer you went to said you could not safely install a trailer hitch receiver on your 2003 Freightliner Springer 2500 Van with the 158" wheel base and factory step bumper, as the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" # 75210 was specifically designed for your van and is a confirmed fit. You will however want to check the owner's manual of your Sprinter to find its towing capacity, and use the lower rating between the hitch and...
  view full answer...
• Will the Thule Elite Van XT 2 Bike Rack Fit on a 2005 Dodge Sprinter Van?
  I do have a good solution for you, however. I confirmed with Thule that the Thule Elite Van XT 2 Bike Rack for Sprinter Rear Door # TH302043 will not fit a 2005 Dodge Sprinter Van. However, the next best solution is to use a hitch and a hitch-mounted bike carrier. For the bike rack, I recommend the Kuat Sherpa 2.0 Bike Rack for 2 Bikes - 2" Hitches # SH22G along with the Kuat Pivot 2 Swing Away Hitch Extender for Bike Racks # PVP20B. The great thing about the Kuat Sherpa 2.0 with the Pivot...
  view full answer...
• Distance Between Mounting Brackets on Draw-Tite Trailer Hitch 75210
  I spoke with Draw-Tite to verify what I know about trailer hitch # 75210. The spacing between the side mounting brackets is 44-1/8 inches. This is a custom fit hitch meaning it was designed to fit only certain vehicles. Specifically it fits 2003 to 2006 Sprinter vans with 140 or 158 inch wheelbase and either single or dual rear wheels. If that is what you have then this hitch will fit.
  view full answer...
  
• Choosing Between Curt 14250 and Draw-Tite 75210 for 2003 Dodge Sprinter Van
  Because we haven't installed either hitch at our facility, I don't have the specific dimensions you're needing, but I can provide a ballpark figure that could be helpful to you. When installed, the top of the receiver tube for either hitch will sit about 1 inch below the rear bumper of the vehicle, which means that the underside of the hitch will sit right about 4 inches below the underside of the bumper. The face of the receiver tube will protrude about 1-1/2 inches past the rear edge...
  view full answer...
• Is Removal of Step Bumper or Spare Tire Required For Hitch Installation on a 2006 Dodge Sprinter Van
  I spoke with my contact at Draw-Tite, and he said that as long as your Sprinter frame is 41 inches wide outside to outside and the wheel base is more than 118 inches long, the Draw-Tite Max-Frame Trailer Hitch, item # 75210, will fit your 2006 Dodge Sprinter Van. You will not need to remove the spare tire for installation of the hitch. The factory step bumper will be re-attached at original position with fasteners provided with hitch. I have included a link to the installation instructions...
  view full answer...
• Which Trailer Hitches Fit a 2006 Dodge or Freightliner Sprinter without a Step Bumper
  There are 5 versions of the 2006 Dodge/Freightliner Sprinter so to determine if there is a hitch that will fit we have to look at which specific model you have. If you have the 118 inch wheelbase, single rear wheel model you can use # 13250 or # 14250 If you have the 140 inch wheelbase, single rear wheel model you can use the same Curt hitches above as well as # 75210 If you have the 140 inch wheelbase, dual rear wheel model you can use # 13265 If you have the 158 inch wheelbase, single...
  view full answer...
• Hitch and Wiring Fits for 2004 Dodge Sprinter
  Both of our primary hitch suppliers, Curt and Draw-Tite, show no vehicle listing for a M-B branded Sprinter for model year 2004. Only a Dodge Sprinter is listed, both 2500-series and 3500-series. You can confirm the correct hitch based on the van's wheelbase and drivetrain. If you click on the "Select Vehicle Style" drop-down menu tool at the top of the linked page you can select your Sprinter's configuration; you will then see the hitches just for that setup. For example, for a 118-inch...
  view full answer...
  
• Will the Draw-Tite Hitch # 75210 fit a 2006 Dodge Sprinter with a Factory Step Bumper
  The Draw-Tite Class III 2 Inch Hitch, part # 75210, is for a 2006 Dodge Sprinter with a 140 inch or 158 inch wheelbase and either single or dual rear wheels. It will not fit the 118 inch wheelbase vehicle. To fit the Sprinter with the dual rear wheels the width between the frame rails will need to measure 35-1/4 inches. On the 2006 Dodge Sprinter, the Draw-Tite hitch # 75210 will fit if you have the factory bumper that is molded to match the design of the vehicle. It will not fit your...
  view full answer...
• Distance From Front And Back Holes To The Edge Of The Receiver On The Draw Tite 75210
  I grabbed a tape measure and went out to our warehouse to measure the Draw Tite hitch # 75210. From the center of the first hole to the edge of the receiver measured 9-3/4". From the second set of holes it is 12-1/2" to the edge of the receiver. I made a drawing for you which I have included below.
  view full answer...
  

Do you have a question about this Trailer Hitch?