Summer Starts Here - Save up to 70%
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Ideal for heavy-duty towing, this vehicle trailer hitch has a cast steel center that is designed to handle hefty tongue weights. Tested Tough guarantee ensures that this durable, corrosion-resistant hitch exceeds industry standards.
Features:
Specs:
Specifically designed for a serious towing machine, this rugged trailer hitch receiver features the strong, durable construction that your heavy-duty applications require. The secure side-bracket design and all-frame attachment system ensure maximum stability. The cast center section lets you pile on the tongue weight without any worries. And the reinforced pin hole and large safety-chain loops better accommodate your heavy-duty towing needs.
Draw-Tite's Tested Tough program provides testing standards far superior to those outlined by the Society of Automotive Engineers (SAE), the go-to source for engineering professionals.
Each Draw-Tite trailer hitch receiver undergoes extensive fatigue testing and static testing with the ball mount that is either supplied or recommended for use with that particular hitch, thus ensuring results that are applicable to real-life use. Fatigue testing is also conducted on hitches rated for use with weight-distribution systems.
In addition, Draw-Tite performs static testing on a simulated automobile, as opposed to the rigid fixture used for SAE testing, resulting in a more true-to-life scenario.
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
California residents: click here
Average Customer Rating: 4.5 out of 5 stars (280 Customer Reviews)
Ideal for heavy-duty towing, this vehicle trailer hitch has a cast steel center that is designed to handle hefty tongue weights. Tested Tough guarantee ensures that this durable, corrosion-resistant hitch exceeds industry standards.Easy installation if everything cooperates. It would be difficult for a single person laying on the ground. Also make sure you spray some sort of lubricant on your bolts that go through the frame. I broke the welds on the welded nuts inside the frame on two of them. Had to burn them off of the torch and fish new bolts into the frame. Also don't Yank on the wires that thread onto the bolts to make them out of shape. They won't fit through the holes if you bend them. Other than a few little problems on my end, everything with the hitch lined up perfectly. It's a nice heavy hitch.
With the simple to follow instructions this hitch will be a snap to install!
It took a bit of doing, which was more an issue with my specific truck, but with some extra 'oomph' we were able to install this hitch in a relatively short time. Am important addition to my vehicle, at a reasonable price point. Ordering and delivery were both quick and painless. I'll order from you guys again when the need arises!
The hitch is well made serves its purpose well however, intstallation on a 2022
Ram was more than could be performed in the driveway. Insallation was finished on a lift with a 5# hammer.
Garbage! This thing was a nightmare to install. It took 2 floor jacks and a dead blow hammer to get it in place, only to find that It was tweeked horribly. If your on a budget, get it. Just know you will need to grind all the holes bigger to make it fit. They will say it’s from metal movement, but that’s BS. It’s poorly packaged. There is no foam to protect the hitch at all. It’s only the cheapest cardboard China has to offer. Upon receiving the hitch the box looked like it had been attacked by a T-Rex. If I hadn’t needed the hitch when it was delivered, I would of sent it back. I gave it 2 stars only because it was cheap.(you get what you pay for…..)
Jenny N.
3/4/2022
I will have our Customer Service team reach out to you. It sounds like that the side brackets were knocked out of alignment which can happen while in transit to our facility or to you. We do have a FAQ that can assist with moving the side brackets of the hitch back into alignment to allow for installation. I also recommend touching up the hitch with a rust resistant paint which you will have on hand for regular hitch maintenance.
couldnt get one crossmember bolt in didnt fit between frame corectly
Jenny N.
10/12/2023
I am wondering if the hitch side bracket is flexed. Would you be able to send a picture of where the bolt is? If it is flexed, I do have a FAQ that can help move it back into alignment.
Helpful Links
Fit of part was almost not going to work with my vehicle. Part arrived at my house in poor packaging. Once part was attached to vehicle it is perfect.
I rarely do a review, but I need to bring this to your attention. The hitch seams very well built but the way the holes lined up with the M-14 bolts lined up with hitch to truck frame was a big challenge! Unless the hitch was bent in shipping (the box was torn and taped up) then you need to fix this. After I was able to start the bolts that you provided with only a little difficulty. I had to use a large pry-bar to rack over your hitch so I could align the holes in the truck frame to reinstall the M-14 bolts. Even with this 2 of the 4 M-14 were cross treaded. So, I had to use a very large power handle to force these bolts tight. The spare tire was not much of a problem or in the way with the install. I have done labor in construction for 40 years, maintenance work and just installed a water pump on my truck. So, I'm not without experience. This took me 4 hours to install...not reasonable. KS
Brooke M.
4/17/2023
Thank you for your concern! It is not uncommon for hitches to be flexed from the shipping process. It sounds like you were able to muscle through and get er done. We do have an article for straightening flexed hitches if this should happen again in the future.
Helpful Links
Does the job! This is my third purchase from etrailer and it has been as advertised each time!
I gave this hitch a 5 star rating, this is for the hitch itself.
The install was greatly added by the use of the fish wires for the bolts.
It took about 3 hours to install this hitch, the fit was extremely tight,
with a floor jack under the hitch and almost picking the truck off the floor
it still took a 4# hammer and a block of wood to persuade the hitch into the frame
after loosening the upper bumper crossmember bolts, the rearmost factory bolts then took two pry bars and four hands to get the last bolt started. Once finally started the bolts pulled the hitch up into position and swaged the hitch into the bumper braces.
The hitch seems to be well built and heavy duty the only problem is the alignment of the two rearmost holes and the extremely snug fit.
The hitch also looks good after the installation was complete, I didn't get a picture of the installed hitch, this was on my son inlaws pickup.
The fitment was tight and snug, the use of a rubber mallet and a second set of hands is necessary. Construction is very stout and well built. My hitch arrived with some scratches to bare metal in the paint finish, kind of unfortunate since they were on the outside where they'll probably show rust soon. The two middle holes mounting to the framerails did not line up, I had to use a carbide grinding bit to widen the holes in order for the bolts to line up and thread in. With that added time, It took about 45min to complete. Fishing the carriage bolts through the frame was not hard at all. This overall fit well and will allow me to pull a trailer with my '12 Ram 1500 ST.
Good product heavy hitch. Box was damaged but seemed ok. difficult to install alone two people install for sure. Fits very tight needed a big hammer to help into place maybe a little damaged during shipping who knows.
Sierra K.
11/1/2021
It may have been a bit flexed which is a common occurrence in hitch receivers. I am glad that you got it installed.
Helpful Links
This hitch is a little bit more rugged than what i will probably need, but I’m glad I bought this one. Shipping was right on schedule. A few minor scratches in the paint but I blame the delivery driver. Hitch was slightly bent from being tossed around during delivery so it took a little bit of maneuvering to line the bolt holes up. Once lined up it went in easy. Probably around 1.5 hours for install time. 19mm and 21mm sockets. Pull wires definitely made it a lot easier. Video explained installation perfectly. Looks great on the truck, have not tried it out yet but I can’t wait to! I’ve bought a few products from etrailer and I’m happy every time. They know their stuff. I would definitely recommend this site to anyone!
Easy install thanks etrailer! Simple, extremely quick shipping and follow up. That's great customer service. Few simple tools 19&21mm sockets ratchet and torque wrench and about 1.5 hrs I had hitch and brake controller installed in my 2017 ram. I used a little anti seize on all bolts.
Love the receiver hitch. It was not that hard to put on and it looks great too..Will be pulling open and enclosed trailers. I submitted a picture of the hitch installed.
Thanks again Adam and Stacey for everything.
The Draw Tite Ultra frame is a beautifully made trailer hitch and very beefy. It looks great and fits perfect. Though it is an Extremely tight fit and took two people to install it about 45 minutes. Highly recommended.
etrailer.com was very helpful with the specifications for trailer hitches, and sent their recommended hitch to us very quickly.
*** Installation was a nightmare. ***
When we first tried to install it from underneath, none of the holes could be aligned. We removed the bumper, and the rear cross-member (that the bumper was bolted to), so that we could assemble it on the ground before putting it in, and it still needed modification. Putting the bolts though with a string as instructed was not a simple task, but it was the easiest part of this installation. The instructions are vague. Once the assembly was put back into the truck, 4 of the remaining holes needed to be modified (the furthest forward in the truck and the middle holes).
It hard to understand how Draw-Tite got the holes to be mis-aligned this much.
It took a day of grinding and some pry bars to get it in.
If I didn't need it soon, I would have sent it back.
The hitch does look and feel strong now.
Hitch went on great after some slight persuasion with a pry bar to line up the factory holes. I thankfully had an impact wrench on hand which made installtion that much better. All in all it took me about hour that from the time i started dropping the spare tire to securing the spare tire. Feels very strong fit nice and snug. The fish wire for the bolts was really handy!
Shipping was a little sketchy, as you can tell from the photo. Not etrailer’s fault...looks like the shipping company didn’t even slow down when they delivered it. Either way, all the parts/hardware were present. Pretty easy install and it seems solid. Haven’t hauled anything yet but I don’t think it is going to be an issue with this thing. Took a little longer than expected, mostly bc I did it alone. Watch the [online] install video. Helped a good bit.
I have a 2017 Dodge Ram 1500. This is the hitch that I’ve been looking for to tow my toy hauler Instructions was easy to read I put the hitch on all by myself it’s a perfect fit can’t wait to try it out. I would recommend this hitch to anybody that’s looking to buy a hitch it is definitely what the picture shows it’s totally heavy duty
Perfect fit and easy to install.Well hidden when not in use on our 2018 Nissan Rogue.
Love this draw tight !!!
Very easy to install , only took me about 30 minutes and that was because I had to locate my tools that someone had barrowed without my knowledge lol..
This will help save my bumper and tag from being damaged from my trailer tong also ..
Fast shipping and easy install! Installed in on my 2016 Ram 1500. Just followed the video and had it on in about an hour. Pretty tight fit just had to shimmy it in there for a second then went right into place. A second pair of hands makes it so much easier. Possible alone if you have some stands to hold it in place I guess. Really happy with it, looks clean!
Very strong and a good fit, a line up pry bar is a big help because it is a tight fit to line up those holes. Hitch is not very intrusive and it tucks nicely under the bumper. Very happy with it and it took me about 50 minutes to install and I didn't even skin my knuckles lol.
Product arrived on time and was easy to install has been a great addition to my truck
Do you have a question about this Trailer Hitch?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Charles
12/30/2023
Good rugged hitch with fantastic weight for tongue and towing!