Expert Review Video:
Front Receiver Hitch Specs:
Features:
Easily attach a variety of accessories to the front of your vehicle with this fully welded, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.
Installation Notes:
No drilling required for installation
Trimming of front air dam and/or fascia may be required for installation
If a front mounted license plate is present, license plate holder relocation or modification is required to install hitch: use part number 8802 or 5443, which are sold separately
Tech Tip:
Front fascia will need to be trimmed to allow access for the hitch receiver opening.
More Information >Front Receiver Hitch Specs:
Features:
Easily attach a variety of accessories to the front of your vehicle with this corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.
Installation Notes:
No drilling required for installation
More Information >Front Receiver Hitch Specs:
Features:
Attach a variety of accessories to the front of your vehicle with this completely hidden, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more. Aluminum and steel alloy construction is sturdy and eco-friendly.
Installation Notes:
No drilling required for installation
Trimming or removal of underbody panel required for installation
Front bumper requires minor trimming
More Information >Videos
for Front Receiver Hitch
Help Articles
for Front Receiver Hitch
Expert Answers
for Front Receiver Hitch
I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light…
view full answer...The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.
view full answer...My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…
view full answer...While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular…
view full answer...Hey Michael, thanks for reaching out! The EcoHitch #EH57FR sits a little higher than the Curt #C52NR so it will give you better ground clearance for your 2024 Chevy Silverado 2500. The EcoHitch is a bit more recessed into the front bumper than the…
view full answer...I spoke with Lippert and they said the Kwikee 35 Series Electric RV 1-Step part #LC3691461 will be a direct replacement for the Coach Steps 725-0041. It will be a bolt-on install for the most part for the exception of changing out the door switch…
view full answer...The factory trailer brake controller port on your 2021 Chevrolet Tahoe is located underneath the dash just to the left of the steering wheel. It will be taped to another harness so it may take a bit of looking to find. Keep in mind that if your…
view full answer...M12-1.5 and 1/2"-20 threads are not going to be interchangeable. The diameter of an M12 thread is only going to be 0.4724" while 1/2" threads are going to be 0.500" in diameter. We currently only have…
view full answer...You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on…
view full answer...From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights…
view full answer...The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be…
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...Filter Products (6)