Expert Review Video:
Front Receiver Hitch Specs:
Features:
Attach accessories to the front of your vehicle with this trailer hitch receiver. Perfect for winches, spare tire carriers and more. Hidden cross tube leaves only receiver visible. Aluminum and steel alloy construction is sturdy and eco-friendly.
Installation Notes:
No drilling required for installation
Front plastic panel will be temporarily removed for installation
Hitch includes a front license plate bracket which installs in the hitch receiver opening when not in use
More Information >Front Receiver Hitch Specs:
Features:
Attach accessories to the front of your vehicle with this trailer hitch receiver. Perfect for winches, spare tire carriers and more. Hidden cross tube leaves only receiver visible. Aluminum and steel alloy construction is sturdy and eco-friendly.
Installation Notes:
No drilling required for installation
Front plastic panel will be temporarily removed for installation
Hitch includes a front license plate bracket which installs in the hitch receiver opening when not in use
More Information >Front Receiver Hitch Specs:
Features:
Easily attach a variety of accessories to the front of your vehicle with this fully welded, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.
Installation Notes:
No drilling required for installation
Tech Tip:
Minor fascia trimming is required only on 4WD models.
More Information >Front Receiver Hitch Specs:
Features:
Easily attach a variety of accessories to the front of your vehicle with this fully welded, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.
Installation Notes:
No drilling required for installation
Tech Tip:
Minor fascia trimming is required only on 4WD models.
More Information >Front Receiver Hitch Specs:
Features:
Easily attach a variety of accessories to the front of your vehicle with this corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.
Installation Notes:
No drilling required for installation
Trimming of front air dam and/or fascia may be required for installation
Tech Tip:
Front tie down brackets will be removed. Hitch cross tube may be mounted with receiver opening in a low or high position. Fascia trimming will be required if mounted in the high position.
More Information >Videos
for Front Receiver Hitch
Help Articles
for Front Receiver Hitch
Expert Answers
for Front Receiver Hitch
I've never heard of an actual third brake light connector on a camper…
view full answer...There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…
view full answer...The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.
view full answer...My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…
view full answer...While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the…
view full answer...Hey Michael, thanks for reaching out! The EcoHitch #EH57FR sits a little higher than the Curt #C52NR so it will give you better ground clearance for your 2024 Chevy Silverado 2500. The EcoHitch is a bit more recessed into the front bumper than the…
view full answer...I spoke with Lippert and they said the Kwikee 35 Series Electric RV 1-Step part #LC3691461 will be a direct replacement for the Coach Steps 725-0041. It will be a bolt-on install for the most part for the exception of changing out the door switch…
view full answer...The factory trailer brake controller port on your 2021 Chevrolet Tahoe is located underneath the dash just to the left of the steering wheel. It will be taped to another harness so it may take a bit of looking to find. Keep in mind that if your…
view full answer...I do have an option for you but we have not yet gotten out hands on a 2019 Chevrolet Blazer therefore, have not had the chance to look for the brake controller wiring port either. I checked with both Tekonsha and Curt and it looks like they have…
view full answer...M12-1.5 and 1/2"-20 threads are not going to be interchangeable. The diameter…
view full answer...From what I could find it looks like your 122R (red) and 122Y (amber) lights measure…
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...Filter Products (10)