Filter Products
Filter Results
$156.67 - $449.99
$651.99 - $785.99
$552.99 - $1,157.03
$552.99 - $1,198.99
$417.94 - $1,157.03
$552.99 - $1,198.99
Filter by Winch Application
$156.67 - $449.99
$651.99 - $785.99
$552.99 - $1,157.03
$552.99 - $1,198.99
$417.94 - $1,157.03
$552.99 - $1,198.99
Videos
for Electric Winch
Help Articles
for Electric Winch
Expert Answers
for Electric Winch
It is plastic. The ComeUp UW-5000si Trailer Winch item #CU645010 is a light duty winch so it's housing and base are made of plastic. I attached a picture below that will show you the base. I've also linked an installation…
view full answer...For your 2007 Ram 3/4 ton, I'd recommend the Curt #C31017 which would mount to the underside of the frame members and would have the receiver tube sitting directly under the front bumper. I spoke with my contact at Draw-Tite who…
view full answer...For a 12,000 lb. electric car trailer winch like the Bulldog Winch Trailer Winch part #BDW10040, I recommend a standard 12 volt lead acid battery rated up to at least 650 cold cranking amps (CCA). As long as the battery is rated up to 650 CCA then…
view full answer...The Superwinch Tiger Shark Off-Road Winch #W85NF that you referenced does not require installing an additional fuse as it has one built into it.
view full answer...If you're going to use a winch to raise and lower your popup you will want a winch that power loads both in and out. With a winch that will only power load in you will only be able to raise the popup and not lower with the winch. We have…
view full answer...For a cost-effective powered car trailer winch you can consider the Bulldog Winch #BDW15019 which includes a roller fairlead and wire rope. This winch offers a 2-minute duty cycle (15 minutes of cool down time is required between cycles) and with a…
view full answer...According to RoadActive Suspension the spring rate for the standard kit #RAS3611-S is 2,400 lbs. For the heavy duty #RAS3611-SHD it is 3,600 lbs. The heavy duty #RAS3611-SLHD is the same but only designed to fit if you have factory top overload…
view full answer...There's a few differences. • The Curt #C31017 is manufactured in the US, while the Draw-Tite #65046 is manufactured in Mexico. • When installed, the Curt hitch will sit higher on the vehicle for more ground clearance. The underside of the…
view full answer...The Bulldog Winch Trailer Winch #BDW10039 is 24" long x 7-1/4" wide x 7-1/4" tall so it will have no issues fitting on your recessed plate on your trailer. The winch includes a mounting plate that is 20" long and…
view full answer...In order to find the correct size wire for a winch you'll need to know the amp rating. The Bulldog Winch Trailer Winch part #BDW10040 for example which has a 12,000 lb capacity and can pull anywhere from 65 - 400 amps depending on the load.…
view full answer...The Superwinch S5500 Trailer Winch #SW1455200 mounting bolt holes are separated apart by 3-3/4" on center (see attached photo). Attached is a review video for you to reference as well.
view full answer...Yes, the Bulldog Winch Hitch Mounted Winch Mounting Plate with Handles part #BDW20011 will work with the Warn Electric Winch M12 as they both use the same industry standard winch mounting hole spacing which is 4-1/2" wide x 10 long.
view full answer...Videos
for Electric Winch
Help Articles
for Electric Winch
Expert Answers
for Electric Winch
It is plastic. The ComeUp UW-5000si Trailer Winch item #CU645010 is a light duty winch so it's housing and base are made of plastic. I attached a picture below that will show you the base. I've also linked an…
view full answer...For your 2007 Ram 3/4 ton, I'd recommend the Curt #C31017 which would mount to the underside of the frame members and would have the receiver tube sitting directly under the front bumper. I spoke with my contact at Draw-Tite who…
view full answer...For a 12,000 lb. electric car trailer winch like the Bulldog Winch Trailer Winch part #BDW10040, I recommend a standard 12 volt lead acid battery rated up to at least 650 cold cranking amps (CCA). As long as the battery is rated up to 650 CCA then…
view full answer...The Superwinch Tiger Shark Off-Road Winch #W85NF that you referenced does not require installing an additional fuse as it has one built into it.
view full answer...If you're going to use a winch to raise and lower your popup you will want a winch that power loads both in and out. With a winch that will only power load in you will only be able to raise the popup and not lower with the winch. We…
view full answer...For a cost-effective powered car trailer winch you can consider the Bulldog Winch #BDW15019 which includes a roller fairlead and wire rope. This winch offers a 2-minute duty cycle (15 minutes of cool down time is required between cycles) and with a…
view full answer...According to RoadActive Suspension the spring rate for the standard kit #RAS3611-S is 2,400 lbs. For the heavy duty #RAS3611-SHD it is 3,600 lbs. The heavy duty #RAS3611-SLHD is the same but only designed to fit if you have factory top overload…
view full answer...There's a few differences. • The Curt #C31017 is manufactured in the US, while the Draw-Tite #65046 is manufactured in Mexico. • When installed, the Curt hitch will sit higher on the vehicle for more ground clearance. The underside of…
view full answer...The Bulldog Winch Trailer Winch #BDW10039 is 24" long x 7-1/4" wide x 7-1/4" tall so it will have no issues fitting on your recessed plate on your trailer. The winch includes a mounting plate that is…
view full answer...In order to find the correct size wire for a winch you'll need to know the amp rating. The Bulldog Winch Trailer Winch part #BDW10040 for example which has a 12,000 lb capacity and can pull anywhere from 65 - 400 amps depending on the…
view full answer...The Superwinch S5500 Trailer Winch #SW1455200 mounting bolt holes are separated apart by 3-3/4" on center (see attached photo). Attached is a review video for you to reference as well.
view full answer...Yes, the Bulldog Winch Hitch Mounted Winch Mounting Plate with Handles part #BDW20011 will work with the Warn Electric Winch M12 as they both use the same industry standard winch mounting hole spacing which is 4-1/2" wide x 10 long.
view full answer...