The trailer hitch I recommend for your 2005 Tribute is the etrailer, part # e56AR. This is a Class lll hitch and it has a 2 inch receiver opening. I recommend going with a Class lll hitch because it gives you a lot more versatility when you want to carry any accessories or when towing. You can use Class l or ll accessories in the Class lll hitch but if you install a Class ll hitch like part # 36501 you will be limited to Class l or ll items.
If you plan on doing some towing you might... view full answer...
We have several trailer wiring options that are confirmed to fit your 2003 Mazda Tribute, but the part # HM48895 that you referenced is not one of them.
Instead you would want the part # 118343 if you don't have the tow package and part # C55255 if you do have it. view full answer...
I think your best bet would be to make a few short test trips to see how the trailer responds. I would suggest driving a few miles on the interstate as well as surface streets at varying speeds.
If the rear of your Tribute sags once the trailer is attached and trailer sway becomes an issue, then I would choose a system appropriate for fully loaded tongue weight of your trailer.
Once you get your trailer, if it becomes evident that weight distribution or sway control is necessary, get... view full answer...
Since your 2005 Mazda Tribute has crossbars that run side to side on the roof I will make my recommendations for it. The Outlander would need to have crossbars added if it only has side rails and that represents additional cost.
I recommend the Rhino-Rack J-style carrier # S512 since it can fold down flat and also has a weight capacity of 99 pounds. You will want to check the roof rack and/or the owner's manual for the Tribute though to make sure it is rated high enough for your 95 pound... view full answer...
For a 2009 Mazda Tribute the most popular brake controller, and the one I recommend, is the Tekonsha P2, # 90885. This controller is reliable, easy to use, and easy to set up.
To install the controller you will first need to have a 4-Way trailer wiring harness on the vehicle, # 118551, if it does not already have one. I have included a link to the instructions and a link to a video showing a typical installation for you.
Next you will need a 4 and 7-Way installation kit # ETBC7. This... view full answer...
Installing this particular hitch on your Tribute should not be too difficult if you have average mechanical ability and access to a torque wrench. One of the connections on each side of the frame uses a weld nut, a nut that is welded into the interior of the frame member.
Since your vehicle has a few years on it, there is a good chance that there is some corrosion and road grime built up in the threads of the weld nut. You will need to spray a lubricant like WD-40 into the weld nuts and... view full answer...
For your 2005 Mazda Tribute I recommend the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118426. This harness will plug into your Mazda Tribute's wiring harness, which is located behind the driver's-side and passenger's-side tail lights just like the Ford Escape video attached.
Once you've plugged in the T-connector, run the hot lead up to your car battery. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal... view full answer...
The only roof rack designed to fit the flush rails on your 2005 Mazda Tribute roof is made by Inno and includes the following parts:
- 42" Square Crossbars # INB107
- Feet # INTR
- Fit Kit # INTR103
If you let me know what you plan on using the roof rack for I can make a recommendation for you! view full answer...
Rhe Thule Ride-On Adapter part TH532 has been discontinued but will only work with bike carriers. This adapter uses plastic mounting hardware and cannot handle the stress a kayak would have and would fail.
You will need to either install a roof rack designed to be able to handle the weight and stress, or if you have crossbars already on your Tribute you can find a kayak carrier that will fit your crossbars.
If you do not have a kayak carrier and you have factory crossbars on your Tribute,... view full answer...
For your wife's 2005 Mazda Tribute we have the Draw Tite hitch part # 75751 which is a confirmed fit and allows you to retain the spare. It's not the best angle but I attached a picture of this hitch installed on a vehicle like yours and you can see that the spare is left installed on it. view full answer...
Yes, if you plan on towing a trailer and not just use it for non-trailer loads like a bike rack or a cargo carrier, you need a wiring harness to power up the trailer lights. If your 2010 Mazda Tribute is equipped with a factory tow package you need item # 118251. If your vehicle does not have a factory tow package, then you need item # 118551. The T-One Vehicle Wiring Harness # 118551 will work either with or without backup sensors. I recommend the 4-Flat Mounting Bracket # 18144 for a... view full answer...
For your 2002 or 2004 Mazda Tribute, for a roof mounted tent like the Yakima SkyRise 2 Person Tent # Y07436 or 3 Person Tent # Y07437 you will need crossbars. If you have the raised factory side rails, then I recommend the Thule bars # TH711220 and Evo Foot Pack # TH710401 with Lock Cores # TH450400. This combination will work well for either tent option.
Unfortunately, if you have the flush mounted factory side rails, there is not a fit that will allow for the weight capacity needs... view full answer...
A hitch from a 2004 Nissan Xterra would not fit a 2011 Toyota RAV4. For your RAV4 I would recommend you get the Curt Trailer Hitch # C13149. This is a Class III hitch with plenty of capacity. Check out the install video I attached.
If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball,... view full answer...
The Thule Passage trunk mount bike rack # TH910XT is indeed a fit for your daughter's 2011 Mazda Tribute. Whether or not it is the best choice depends on what you are looking for in a trunk mount bike rack. I can tell you that the Passage is a solid performer that has not required any major changes over the years.
The Passage uses 6 straps to attach to the rear of the vehicle. The first time you perform the installation takes the longest but each subsequent time will be easier since you... view full answer...
To get your 2006 Mazda Tribute V6 ready to tow your mini RV you'll need a trailer hitch, wiring for both the trailer lights and brake system (with a brake controller), and most likely a weight distribution system. From what I could find in the owner's manual it looks like your vehicle has a max trailer weight rating of 3,500 lbs but you'll want to confirm that in your copy of the owner's manual.
Below is a list of the parts that I recommend for towing with your Tribute:
Trailer Hitch... view full answer...
While I have a much easier trailer wiring solution than the # 40455 that you referenced for your 2006 Mazda Tribute there is a good chance you'd have to have a relay installed behind the dash board of your vehicle to have the circuits active for this kit to work. Since most of our customers have come back and stated that finding the relay was a headache the much better option is to go with a harness that installs by plugging inline with the taillight circuits of the vehicle.
For that I... view full answer...
Go To Results