Yes the Reese conical washer part # 01292-008 will work with the install hardware of the Curt hitch # C12221 that fits your 2007 Pontiac Vibe. view full answer...
We do have trailer hitches that are specifically designed to fit the GT model of the 1999 Pontiac Grand Prix. You can use the Curt # C12225. I have included a link to the installation details for reference.
If you plan on doing some towing, the recommended ball mount is # 36065 for use in the rise position only. For a pin and clip, use # PC2. For a ball, you can use # 19256 (1-7/8 inch diameter) or # 16258 (2 inch diameter). For trailer wiring, you can use 4-Pole Hardwire Kit Including... view full answer...
Flat towing a vehicle is always subject to the okay of the auto maker and the best place to check this is in the owner's manual (or with your local dealership which can see the car's specific factory-installed equipment by looking up its VIN). Page 4-26 of the online edition of the owner's manual indicates that one version of the car cannot be flat towed, that version being the 3.9L V6 engine with the four-speed automatic transmission. Since you have the 3.5L you can flat tow the car but... view full answer...
According to Curt Manufacturing, the # C11117 is a fit for all models of the 2001 Pontiac Firebird, including the T/A. For trailer wiring, you'll want to use # 119178KIT. Curt recommends the # C45520 ball mount along with the # PC2 hitch pin and # A-80 for a 1-7/8 inch or # A-82 for a 2 inch hitch ball.
I'll link you to our return policy. view full answer...
It is fine for there to be a slight curvature, as that won't affect the fit of the Trunx Rooftop Cargo Carrier # TRX44FR.
That said, you do still need to ensure it fits, and to do that you just need to take a couple measurements. First thing to do is measure the crossbars, as they need to be a maximum of 3-3/4" wide x 1-3/16" tall. The vast majority of factory crossbars are less than this but you do want to verify.
Next measure from center to center of your crossbars, and if it is between... view full answer...
Yes, the Derale Oil Filter Relocation Kit # D15748 will fit your 1965 Pontiac GTO with the 389ci engine. Your oil filter uses a 13/16"-16 thread diameter. We also have the Derale Oil Filter Relocation Kit # D15716 specifically for the 13/16"-16 threads. You can also use the Derale Dual Mount Oil Filter Relocation Kit # D15749 if you wish to use 2 filters.
The PTC Custom Fit Engine Oil Filter # 351P1A is the new filter size you will need to use with any of the 3 relocation kits. view full answer...
Yes, the full size spare will need to be lowered to provide access to the hitch attachment points, but will fit back into its original location after installation of the Curt Class III Trailer Hitch, item # 13336.
You will need to Lower the spare tire from its storage location. It will be put back in place after hitch is installed. I have included a link to the instructions for this hitch for you to review. We also have a installation video showing the installation of this hitch for you... view full answer...
The SportRack Explorer Cargo Box, # SR7018, is a semi-universal fit item made to fit as many roof racks as possible. As long as the crossbars on your 2003 Pontiac Vibe have a center to center distance between the bars of 23-5/8, 25-7/8, 27-7/8, or 29-7/8 inches, the box will fit. I have included a link to the installation details for you. view full answer...
On your 2000 Pontiac Grand Am 4 door the SportRack Semi-Custom Roof Rack for Naked Roofs SR1004 was a confirmed fit but has been discontinued by the manufacturer. It has a mandatory fit location with a crossbar spread of 23.5 inches. It cannot be moved from the mounting locations to fit the Thule Interstate Rooftop Cargo Bag # TH869 between the rails, but because the bag is flexible, you can load your cargo between and over the bars without issue. This combination will give you the stability... view full answer...
The Blue Ox Base Plate Kit part # BX3231 is a suitable base plate for the 2007 Pontiac G6 Convertible. The Blue Ox Base plate is a nice choice that features removable base plate tabs for a discreet install. The Blue Ox Base plate is only compatible with the following Blue Ox Tow Bars: Acclaim, Adventurer, Aladdin, Allure, Alpha, Avail, Aventa, and Trion tow bars so you do wan't to be sure you have one of those tow bars to use this base plate.
If you do not have a Blue Ox Tow Bar, I recommend... view full answer...
Your 2010 Pontiac Vibe can be fitted with either of two hitch classes, either a light-duty 1-1/4-inch Class I hitch or a higher-capacity Class II type (also 1-1/4-inch size) depending on the version of the Vibe you have. For reference the hitches we offer for your Vibe are linked at right.
It sounds like you have a Class I hitch and a non-compatible Class II ball mount. Some Class I hitches have a stop inside the tube to prevent use of ball mounts that are not rated Class I. We do not... view full answer...
According to Roadmaster, the Roadmaster XL Base Plate Kit, # 3132-1, that you have referenced is the correct kit for the earlier model 2009 Pontiac G6 models before the updated fascia. This base plate kit fits all models except the GXP and convertible, so this is the right kit for you.
There are several other items that you will need to flat tow your G6. I have incldued a link to an article on the 5 basic components needed to flat tow a vehicle. I have also incldued a link to our series... view full answer...
I spoke with my contact at Tow Ready about converter # 118158. He said that at most the converter is rated for 2.1 amps per side for brake and turn signals so it would not work for you.
I recommend going with a kit that bypasses the vehicle wiring such as a bulb and socket kit, # BX8869, or a magnetic kit such as # RM-2120.
I have included some links to articles on tow bar wiring for you that should also help. view full answer...
The Draw-Tite # 36288 Class II Trailer Hitch w/ Drawbar is a fit for your 2001 Grand Am SE Coupe. If you'll be towing a light trailer, you'll need a few other items to complete your towing system:
Trailer wiring harness with 4 pin trailer connector # 119178KIT
Ball mount # 36071
2 inch trailer ball # 19258
1-7/8 inch trailer ball # 19256
I've linked an install video for the trailer hitch. view full answer...
Having the cargo bag, # TH868, between the rails would be ideal, but it can also sit on top of the bars. If you can place it between the bars, make sure the bottom of the bag and the roof are clean to avoid scratching the paint. view full answer...
The CurtTrailer Hitch Receiver Hitch, # C12225, for the 2008 Pontiac Grand Prix is actually a class II hitch so it will not have the protrusion that will prohibit Class II devices.
The protusion that you have heard about is on the Class I hitches since they can be easily overloaded when using a Class II device. So that protrusion is there as a safety precaution. This will not be a problem for you since this Curt hitch is a class II. view full answer...
The only difference is that Curt has one trailer hitch that fits a 2004 Pontiac Vibe GT, part # C12221 and one trailer hitch for a 2004 Pontiac Vibe NON-GT, part # C12234 while the Draw-Tite # 24812 will fit both models.
The Draw-Tite hitch is a Class I hitch which requires the use of Class I accessories so my recommendation is to go with the option from Curt, with the right hitch depending on if you have a GT or not.
Both the Curt Trailer Hitch # C12221 (GT models) and # C12234 (non-GT... view full answer...
The BTR E-Z Lube Spindle for 2,000-lb Trailer Axles part # TRU44FR will work with the Trailer Idler Hub Assembly for 2,000-lb E-Z Lube Axles part # AKIHUB-440-2-EZ-2K and has a built-in grease zerk for easy lubrication. view full answer...
Passing the power wire through the fire wall is different on almost every type and year model of vehicle. It sounds like you have found some entry points through the fire wall to wire the power wire of # C59236. If you can find a grommet with fewer wires running through it, you can try to cut a small slit on the side of the grommet and push the power wire through that. It is okay for the power wire to be pass through an existing hole with other wires just be careful not to puncture any... view full answer...
Go To Results