bing tracking image

Filter Questions and Answers:

reset filter

Expert Answers about Ford Focus


  • Installing Trailer Wiring Harness on a 2004 Ford Focus
  • It looks like you have purchased wiring harness # 18252 which is correct for a 2004 Ford Focus. This vehicle does not require a converter because it has what is called a combined lighting system. This means the brake lights and turn signals are combined onto one circuit. This is the same way most trailers are wired. You will use the included circuit tester to tech the wires behind the tail lights on the vehicle. Starting on the drivers side, where you will be attaching 3 of the wires,...
    view full answer...

  • Can the Arms on the Swagman XC Bike Rack be Locked
  • Swagman XC 2-Bike Rack Platform Style for 1-1/4" and 2" Trailer Hitches Item # S64650 does not have lockable arms so what we recommend is to use a cable lock such as # S64031 which also includes a hitch lock.
    view full answer...

  • What Parts of Curt Trailer Hitch 11319 Are Visible on a 2008 Ford Focus
  • Once the Curt Class I Receiver Hitch, part # 11319 is installed, the receiver opening where the draw bar slides in will be situated just below the rear bumper. The receiver opening and consequently the drawbar will be visible. The cross tube would be pretty well concealed behind the bumper.
    view full answer...

  • Can Blue Ox Patriot Braking System be Powered by 12V Wire from RV 7-Way
  • The Blue Ox Patriot Portable Braking System # BLU37TR referenced in your question is designed to draw power from the battery in the towed vehicle by simply plugging in the included 12V cigarette outlet adapter inside the vehicle. It's very unlikely that the 12V wire from the RV's 7-Way (which would instead be getting power from the RV's battery) would carry enough amperage to reliably power the Patriot by the time it reached towed vehicle. Because of this and the fact that the install...
    view full answer...

  • Is Drilling Required to Install Curt C11294 Class I Hitch on 2005 Ford Focus ZX4
  • The Curt # C11294 Class I hitch is a fit for Sedan and Hatchback models of the 2005 Ford Focus, unless it's an SVT model. Drilling is not required for the Sedan models, but for hatchback models you will need to drill one 1/2 inch diameter hole in the passenger side frame rail.
    view full answer...

  • Removing the Tail Lights on a 2012 Ford Focus Hatch Back for Trailer Wiring Installation
  • You will need to remove some trim panels in the rear cargo area of your 2012 Ford Focus in order to gain access to the tail light wiring. If you look at the instructions I have linked for the Curt wiring harness, # C56140, there are some helpful pictures. The tail lights may need to be persuaded slightly because the seals around them can stick. If there are additional fasteners holding on the lights, they may be revealed when you remove the trim panels in the cargo area.
    view full answer...

  • Which Vehicles Wires Are Used When Attaching A 4-Way Trailer Connector To A 2005 Ford Focus Wagon
  • You will need to find the vehicles wiring harness that goes to the taillights on your 2005 Ford Focus Wagon. You will need to use a circuit tester like part # PTW2993, to probe the wires and find the correct functions for connecting the wires from your 4-way trailer connector. I am including a video link of connecting a 4-way trailer connector to a 2006 Ford Taurus. It will show you how to probe the wires and how to connect them. On the Ford vehicles the wire colors are as follows, the...
    view full answer...

  • Installation of the AirLift Springs on a 2006 Ford Focus Sedan
  • You will not need any special tools to complete the install of the Air Lift AirLift 1000 Air Helper Springs # AL60723. The installation is pretty straightforward and will only require the drilling of a 5/16 inch hole for installing the inflation/deflation valve. To see exactly what is required to install this product check out the installation instructions that I attached. You will not need to compress your springs to install the air spring, basically you will only need to jack up the...
    view full answer...

  • Measurements for Installing the SportRack SR1010 Roof Rack on 2015 4-door Ford Focus Sedan
  • The measurements for the SportRack Semi-Custom Roof Rack # SR1010 to fit on your 2015 Ford Focus 4-door are: Bar scale: front 26, rear 24. Rack Placement: front bar (A) 10”, back bar, 24” Bar spread: 24” Weight Limit: 90 lbs.
    view full answer...

  • Using Battery Charger Included With HM39530 Brake Buddy When Negative Battery Cable is Disconnected
  • We've got a solution for you. You'll want to use a Deka Quick Disconnect Battery Terminal, part # DW05312. On the terminal end that remains on the battery once disconnected, you'll attach the ground wire for the charger using a # DW05705-1 ring terminal. This leaves the charger grounded once the negative battery terminal is disconnected. I've provided a photo showing where to place the ring terminal.
    view full answer...

  • Torque Value of Install Bolts for Hitch on 2016 Ford Focus Hatchback
  • The Draw-Tite # 75270 is a fit for a Honda Odyssey, and wouldn't fit your 2016 Ford Focus hatchback. We don't publish the torque numbers because they can change over time, but the installation instructions for the hitches mentioned below are linked for you, and each install sheet does clearly list the torque values. The hitch you need will depend on which sub-model Focus you have. For the RS, I'd recommend the Curt # C11489. For the S ,SE or Titanium model, I'd go with a concealed crossbar...
    view full answer...

  • Installation Photo of EcoHitch Hidden Hitch on 2012 Ford Focus Electric
  • I have attached a photo of the EcoHitch Hidden 2 Inch Trailer Hitch Receiver installed on a 2012 Ford Focus Electric. The hitch is designed to fit 2012 through 2014 Ford Focus Electric vehicles. If you're in the market for a bike rack, the Swagman XTC-2 2-Bike Platform Rack # S64670 would pair up nicely with the EcoHitch receiver. If instead, you plan on towing a small trailer, you may consider the following parts to complete your towing package: # 118549 - 4-Pole Flat Trailer Connector...
    view full answer...

  • What is the Torque Spec of the Spindle Nut on a Dexter E-Z Lube Axle
  • In order to remove the hub/drum on your trailer you will want to first remove the spindle nut. Once the spindle nut is removed you are going to want to take a hammer and tap the outer portion of the drum as well as the hub face a few times to break loose an rust/dirt. You should then be able to pull the drum off. Once the drum is off you can wipe down the spindle and then spray the braking assemblies with brake cleaner. You can then install the drum and spindle nut. The spindle nut will...
    view full answer...

  • Installation Process for SportRack Roof Rack SR1002 on 2010 Ford Focus 4-Door
  • I confirmed with SportRack that their square bar roof rack system # SR1002 is indeed a correct fit for your 2010 Ford Focus 4-door. I reviewed an installation video for a similar Yakima roof rack on a 2011 Focus 4-door and this video is linked for you. If you refer to the 52-second mark in the video you'll see how the clamp for that Yakima rack is positioned on the roof line, above the weather stripping. I also linked a close-up photo image from the video. Your SR1002 clamps will install...
    view full answer...

  • Availability of Battery Disconnect Switch for Flat Towing 2016 Ford Focus
  • Disconnecting the negative battery cable in your 2016 Ford Focus, either manually or via a switch, will still allow the battery to provide power to a braking system like the SMI Stay-IN-Play DUO # SM99251 referenced in your question. This is because disconnecting the negative cable will disconnect the battery from the vehicle, but will not prevent it from providing power to other components. If you are interested in installing a battery disconnect switch in your Ford Focus, you can use...
    view full answer...

  • Settings for SportRack Roof Rack on a 2012 Ford Focus Sedan
  • SportRack roof rack # SR1010 is a fit for the 2012 Ford Focus sedan but not the hatchback. If you have a hatchback then you would need a different roof rack. I spoke with my contact at SportRack and asked about the dimensions on your 2012 Ford Focus. They told me that for your vehicle the measurement for the front crossbar is 10 inches from the center of the door jamb to the center of the front feet, the rear crossbar is 24 inches from the center of the front crossbar to the center of...
    view full answer...

  • Mounting Dimensions of the SportRack Semi-Custom on a 2014 Ford Focus Sedan
  • I have attached the mounting dimensions of the SportRack Semi-Custom Roof Rack for Naked Roofs part # SR1010 on your 2014 Ford Focus Sedan for you. The front crossbar will need to be set at the 26 mark and the rear at the 24 mark in regards to width. In regards spread, the front crossbar will need to be positioned 10" forward of the point where the two doors meet and the rear crossbar will need to be positioned 24" back from the front crossbar.
    view full answer...

  • Does Trailer Hitch for 2018 Ford Focus Require Frame Drilling
  • The Curt trailer hitch for your 2018 Ford Focus is the part # C11158 is rated at a 5/10 difficulty level and should take approximately 30 minutes to install. It does require drilling to install. I attached an install video for this for you to check out as well.
    view full answer...

  • Installing Brake Controller and 7-way Trailer Connector on 2014 Ford Focus
  • If your trailer has electric brakes and a 6-or7-way trailer connector, you'll need to install a brake controller on your vehicle to actuate the trailer brakes. Before attempting to tow your trailer, I'd recommend you determine the fully loaded weight of your trailer, and ensure it doesn't exceed the towing capacity of your Focus. If your trailer weighs less than the towing capacity of the vehicle, you'd begin by choosing a brake controller. The Tekonsha Primus, part # TK90160 is a reasonably-priced...
    view full answer...

  • Why Does the Heat Shield Need to Be Trimmed to Install a Draw Tite Hitch on a 2012 Ford Focus
  • The heat shield will need to be trimmed so that you can bolt up the side brackets of the hitch to the bottom of your vehicle frame. If the heat shield was not removed it would not provide a solid surface for the hitch to attach to. Check out the installation instructions link I attached that shows the area where the heat shield will need to be trimmed.
    view full answer...