The Curt hitch part # C11379 that you referenced has been confirmed as a fit for your 2015 Subaru BRZ so it would work well for you.
I looked up pictures of your vehicle and the trunk looks like it opens basically straight up so it would not interfere with a bike rack like the Swagman XTC part # S64670 so it should work well for you.
Curt requires the use of their stabilizer strap part # 18050 when using their hitch to carry a non-supported load like a bike rack. I attached a review video... view full answer...
We have a great roof rack option for your 2014 Subaru BRZ but it does require some drilling of the roof ditch to install rivets with the Rhino Rack part numbers # RRVA118B-2, # RRRDM01, # RRRLKVA, and # DK290. You will need a drill and a drill stop is recommended so you don't drill too far. The channel cover is held back in with the roof rack feet installed. There are plastic caps that can be used to hold the channel in when not in use that are included.
With that installed you could use... view full answer...
Since the Curt Trailer Hitch Receiver # C11379 does require Stabilizing Straps # 18050 you will want to use the Draw-Tite Sportframe Trailer Hitch Receiver # 24935. This is a class I receiver that will give you a 1-1/4 in receiver on your 2013 Subaru BRZ.
The Kuat Sherpa 2.0 Bike Rack # SH12B is one of our easiest bike racks to use. Its lightweight aluminum construction allows you to carry 2 bikes up to 40lbs each and only weighs 32lbs itself.
You may need the T-One Vehicle Wiring Harness... view full answer...
I do have an option for you, however the Curt Trailer HItch Receiver # C11375 that you referenced is designed for the 2014-2016 Scion tC and will not fit your 2015 Subaru BRZ.
For your Subaru I instead recommend the Curt Class I Round Tube Receiver Hitch # C11379. This custom hitch will use existing holes in the vehicle's frame for a no-drill installation. All the needed hardware is included. I have attached the written installation instructions that you can also check out.
If you will... view full answer...
The design of the Draw-Tite Trailer Hitch Receiver, # 24935, will allow to install the hitch without cutting or modifying the bumper or body in anyway. The attached instructions will explain the installation procedures for this hitch.
As for the suspension or brake upgrades, unless the suspension dropped the OEM ground clearance, you will have no issues with this hitch. If the ground clearance has dropped then there may be an issues with the hitch receiver dragging when entering driveways... view full answer...
Yes, to install the Draw Tite hitch part # 24935 that you referenced the rear panel does have to come off. In the instructions link that I attached this entire process is covered.
For trailer wiring you then would want the part # 118629 which is a confirmed fit for your 2017 Subaru BRZ and would work well. view full answer...
If your 2013 Subaru BRZ has no existing rails or crossbars, the 2013 Subaru BRZ Roof Rack by Rhino Rack is a confirmed fit. To have the complete system, you will need the Rhino-Rack 2500 Roof Rack with Square Crossbars # RRVA11B-2, the Ditch Brackets for Rhino-Rack RLT600 Quick Mount Legs # RRRDM01, Leg Kit # RRRLKVA, and the Custom DK Fit Kit for Rhino-Rack 2500 Series Roof Rack Legs # DK290.
I have linked to this article product videos and the entire list of roof rack systems that... view full answer...
The instructions for the mounting kit # RRRDM01 for the Rhino-Rack Roof Rack are meant to generic instructions to fit multiple vehicles. There are no specific installation instructions for your 2016 Subaru BRZ. The instruction for this mount kit are attached to this page for you to review.
I have an alternate solution to using a roof rack for you. I recommend installing a hitch to use a bike hitch and ski and snowboard adapter on your Subaru.
I like the Curt hitch for your vehicle, #... view full answer...
The only roof rack options we have for your 2016 Subaru BRZ are ones that require riveting the fit kit to the roof of the vehicle like the Rhino Rack roof rack part numbers # RRVA118B-2, # RRRDM01, # RRRLKVA, and # DK290.
This will provide you with aero shaped crossbars that will work well with your snowboard rack most likely. view full answer...
I have a great solution for your tire size of 225/45-17 on your vehicle. I recommend the Konig Easy Fit Chains part # TH04115095 because these chains install literally in a matter of seconds, provide great traction, do not require much wheel well clearance, and will last you a very long time. view full answer...
For your 2014 Subaru BRZ I recommend the Yakima FullBack rack # Y02634. This rack was designed with vehicle spoilers in mind. It has a long reach to go up and over a spoiler. I have included a link to a video review of the rack for you.
If the bike you will be carrying does not have a top frame bar that goes straight across (like a typical men's bike would) then I recommend using bike adapter bar # 64005. This will allow you to carry those bikes more level and will provide better ground... view full answer...
The best trunk mount bike rack we have for your 2019 Subaru BRZ is the Yakima FullBack 2 Bike Rack part # Y02634 because it will sit up and over the rear spoiler (if equipped), it offers exceptional ground clearance which is needed for vehicles that sit lower to the ground like your Subaru BRZ, and it has sturdy foam pads to prevent any damage to the vehicle's finish.
The Yakima FullBack has anti-sway cradles to keep the bikes from banging into each other and a sleek black powder coated... view full answer...
The EcoHitch Stealth Trailer Hitch Receiver # 306-X7293 that you referenced weighs exactly 24.5 pounds.
The custom hitch features a towing capacity of 1,000 pounds and a tongue weight limit of 200 pounds. view full answer...
To install the Draw-Tite # 24935 on a 2020 Subaru BRZ, the rear bumper cover and bumper beam must indeed be temporarily removed so the hitch can be sandwiched between the beam and the structure of the chassis. The print I provided from the linked installation instructions should give you an idea of how the hitch fits on the vehicle. view full answer...
The Curt Trailer Hitch Receiver # C11379 is going to be our easiest receiver for a novice installer on your 2017 Subaru BRZ. I have linked the installation instructions below that you can reference to determine if you feel comfortable installing the receiver.
The EcoHitch Stealth Trailer Hitch Receiver # 306-X7293 is far more complicated to install and requires the removal of the rear fascia and impact structure to complete. I feel this is better left to those with more experience to... view full answer...
While I don't have that exact figure I can help you figure out the distance from the ground to the top of the hitch opening when the EcoHitch part # 306-X7293 is installed on your 2019 Subaru BRZ. The hitch opening is going to be right underneath the rear bumper fascia so you can measure from the ground to about 1/2 inch below the rear bumper fascia and take the difference between that and the 18 inches you measure for your trailer coupler and you'd know how much rise/drop you'd need from... view full answer...
The operation of the Erickson Tie-Downs with the Multiplier Ratchet like part # EM58511.
I have attached a video that shows how the tie-down is used to tighten and also release the tension. You can check out the attached photo of the Multiplier Ratchet with some of the features pointed out. The release lever is pulled up to disengage the ratcheting handle. As the video shows, to lock it in position after tightening you would pull the release lever and move the handle down until it is... view full answer...
Go To Results