The Curt Trailer Hitch Receiver - Class I # C11576 is a confirmed fit for your 2018 Toyota Camry. We haven't had the chance to install this hitch yet for photos or a video, but I've attached a photo of this hitch on a 2018 Toyota Camry to assist.
We also haven't had the chance to measure ground clearance due to this, but based on the photo and the 16-19 inch wheels available on the 2018 Camry, it appears you will have 12 inches of ground clearance or more.
It is less visual and it has... view full answer...
The trailer hitches available for your 2014 Toyota Camry all have essentially the same design, they will hang down from the frame and a crosstube will run behind the hitch receiver from one bracket to the other.
I have measured these hitches in the past and found that the Curt # C12107 hangs down a little more than 1/2 inch further than the Draw-Tite # 36540. Another thing to consider when choosing a hitch, is that the Curt hitch has a round crosstube, while the Draw-Tite has a square... view full answer...
The Draw-Tite trailer hitch, # 36416, will fit a 2007 Toyota Camry Hybrid. A Toyota dealership might install it but I recommend going to a trusted mechanic or an RV dealer or shop that works on trailers to have it installed if you do not want to tackle the project yourself.
I have included a link to the installation details and a link to a video showing a typical installation for you.
If you plan on doing some towing the correct ball mount is # 36071 and you can use pin and clip # PC2.... view full answer...
The RockyMounts MonoRail Solo Bike Rack for 1 Bike # RKY10007 is designed to carry a bike that weighs a maximum of 60-lbs, so if after the battery is removed your bike weighs less than 60-lbs, you'll be good to go.
If not, you'd have to look at another alternative bike rack that can accommodate a heavier bike like the Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes # HLY84FR, which can hold two bikes that weigh up to 80-lbs per bike. view full answer...
The transmission temperature on your 2004 Toyota Camry should run through the computer and be accessible through the OBD-II port using the Edge Insight, # EP84130. The parameters that you could potentially monitor include:
Battery Voltage
Intake Air Temperature (IAT)
Engine Oil Pressure (EOP)
Engine Coolant Temperature (ECT)
Engine Oil Temperature (EOT)
Transmission Fluid Temperature (TFT)
Miles Per Hour (MPH)
Miles Per Gallon (MPG)
Revolutions Per Minute (RPM)
1/4-mile and 0 - 60 times
If... view full answer...
It is possible that you may not have to trim the heat shield to install trailer hitch # 36540 on your 2017 Toyota Camry. As long as the hitch installs correctly and is contact with the frame (which means nothing is sandwiched between the hitch and frame) then you will be good to go.
If you will be doing any light towing with the hitch the recommended ball mount is # 36071. For compatible balls you can use # 19256 for a 1-7/8 inch ball or # 19258 for a 2 inch.
And for trailer wiring you... view full answer...
Yes, if you're wanting to only have one set of hoops on the Curt 2 Bike Platform Rack for Fat Bikes # C18085-FB you can remove the other set by turning the locks in a counter-clockwise direction to loosen them from the rack and then slide them off. view full answer...
I have a solution for you. Unfortunately, there is no way to guarantee that the Rampage 4-Layer Outdoor Vehicle Cover - Gray - 15' 1" to 16' Long # RA1304 will secure in any way during transport. This is especially true at higher speeds.
However, depending on your tow bar/base plate setup on your 2014 Toyota Camry, you can use a rock guard like the Roadmaster Guardian Rock Guard # RM-4000 or the Sentry Deflector for Demco Tow Bars # DM9523135.
If you wish to explore this option, feel... view full answer...
All of the hardware you will need is included with the Draw-Tite Class II Hitch # 36540 and it is compatible with your 2014 Toyota Camry. I've attached an installation video for you to see as well.
For a Class II Drawbar # 36071 will fit and includes the clip and pin.
And for Hitch Balls:
# 19256 for a 1-7/8 inch.
# 19258 for a 2 inch.
Finally, for a wiring harness you will want part # 118405. view full answer...
Typical torque specifications for the CURT Class II Trailer Hitch, item # 12343, are listed in the hitch instructions, see link. At the bottom of page one, step 6 lists the torque specifications for your vehicle.
When you purchase the hitch for your vehicle, you will want to use the torque rating that is recommended in the instructions provided for the hitch. Manufacturers change these ratings from time to time so using the instructions provided with the hitch will give you the most up... view full answer...
When routing the power wire to the battery in trailer wiring harness, # 118482, you will want to avoid any areas that may pinch the wire, causing it to break. Any moving components like the suspension can potentially pinch the wire, so avoid moving parts.
You will also want to avoid parts that get hot enough to melt the wire. Exhaust components as an example get very hot and can melt the insulation. However, on the 2011 Toyota Camry, the battery should be in the trunk and you will not... view full answer...
For the Draw-Tite Trailer Hitch, # 36336, for the 1992 to 1996 Toyota Camry, 2 door and 4 door, we rate the difficulty of installation as a 5 out of 10. We base the scale on the estimated installation time. A 5 out of 10 indicates that it should take a novice installer with the correct tools and an assistant about 50 minutes to install the hitch.
I have included a link to the installation instructions for this trailer hitch which lists the tools needed and the steps for installation. You... view full answer...
For your 2011 Toyota Camry 2.4L, you will not need to remove the battery to install the Kat's Heaters Custom Fit Engine Block Heater - Cartridge Style - 120V - 400 Watts # KH11813. The plug will install in the rear left of your engine block. I've attached a video to help and have attached a photo on the specific location on your vehicle. view full answer...
Curt trailer hitch # C11576 is a fit for the 2018 Toyota Camry XSE but we do not have a picture showing it installed on that specific model. I have included a picture on an SE model from the instructions. I have also linked those instructions for you.
The installation is not all that difficult it just takes some time to complete all the steps.
If you plan on towing then the recommended ball mount is # C45521. For a 1-7/8 inch ball use # A-80. For a 2 inch ball use # A-82. And for trailer... view full answer...
We had one customer who moved some wires on their Curt # C34FR harness to allow it to work on the hybrid models of the vehicle. Here's what they tried that worked for them:
"After a little investigation with a meter I noticed the wire for the right/left turn signals coming off the two pass thru connector sets did not line up with the wire connected to the blinker on the car. I cut and re-soldered the wire so on the right side/passenger side the tap off wire matched the car blinker wire... view full answer...
Draw-Tite lists two Authorized Dealers within 10 miles of your location:
Centreville Manufacturing
2023A West St
Annapolis, MD US 21401
(410) 224-2887
or
Annapolis RV
117 Ferguson Rd
Annapolis, MD US 21409
(410) 280-0800
The installation of the Draw-Tite # 36540 is not terribly difficult. If you are reasonably handy, you might be able to complete the installation yourself. Take a look at the installation instructions I have linked you to, you might find that the installation is something... view full answer...
The Curt Support Strap # 18050 is required to be use for any non-trailer loads, like a bike rack or cargo carrier, when carrying them on a Curt trailer hitch receiver, like # C12107 that fits your 2016 Toyota Camry.
If you're using a different hitch that isn't a Curt you can use the bike rack without the strap.
If you're using the Curt hitch, any bike rack requires the strap. view full answer...
Hitch rattle isn't a super common issue but there are some easy ways to relieve the noise. The easiest solution is to bend the exhaust hanger up so that the muffler sets further above the hitch.
If bending the hanger does not provide a solution, another option is to try and replace the rubber exhaust isolater with a shorter isolater. The shorter isolater will help raise the tailpipe up futher away from the hitch.
I have attached a help article that covers these ways to help correct... view full answer...
To clean the weld nuts to install the Draw-Tite Class II Trailer Hitch Receiver # 36336 you'll need a thread tap the same as the M10 fasteners which is 10 mm by 1.25 inches. I've attached a help article and video about cleaning weld nuts that you might find helpful as well. view full answer...
I can confirm for you that the bumper on your 2017 Toyota Camry will remain unmodified after installing Curt hitch # C12107. If you take a look at the install video I've linked, you'll notice that the bumper stays as it was before the installation.
Keep in mind that Curt requires the use of stabilizer straps, # 18050, with this hitch to keep the warranty in tact with non-trailer loads, which are things like bike racks and cargo carriers. I've added links to a pair of videos showing you... view full answer...
Go To Results