2018 Toyota Camry with Curt Trailer Hitch Receiver Ground Clearance

Question

Question:

Do you have any pictures of the Curt Hitch C12176 on a 2018 Toyota Camry. I am concerned with how visible it will be and how much ground clearance it will have? Thanks

asked by: Wayne S

1

Helpful Expert Reply:

The Curt Trailer Hitch Receiver - Class I # C11576 is a confirmed fit for your 2018 Toyota Camry. We haven't had the chance to install this hitch yet for photos or a video, but I've attached a photo of this hitch on a 2018 Toyota Camry to assist.

We also haven't had the chance to measure ground clearance due to this, but based on the photo and the 16-19 inch wheels available on the 2018 Camry, it appears you will have 12 inches of ground clearance or more.

It is less visual and it has a hidden crossbar. I have attached installation instructions and an install of it on a 2020 Camry.

expert reply by: Jason S

1

click to enlarge

Answer 1

The Curt #C11576 hitch that is designed for your 2021 Toyota Avalon do have decent ground clearance. I do have to mention that the measurements are from installs we did with this hitch on a Toyota Camry, so they may be a little different from where…

view full answer...

Answer 2

Yes, we have had a couple of reviews for the Curt Trailer Hitch item #C11576 being successfully installed on a 2023 Toyota Camry XSE. This hitch is custom fit and bolts to your vehicle with included hardware. I really like the Curt hitch because it…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

2018 Toyota Camry with Curt Trailer Hitch Receiver Ground Clearance

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching