Black power coated, 16" steel wheel features an 8 on 6-1/2 bolt pattern and meets Department of Transportation standards.
Features:
Specs:
Determining the Bolt Pattern
The first number in the bolt pattern is the number of bolt holes. The second number denotes the diameter, in inches, of the circle on which the bolt holes sit.
To determine the bolt-circle diameter on wheels with an odd number of bolt holes, measure from the center of any bolt hole to the point halfway between the two bolt holes directly across from the first. (Example: "5 on 4-1/2" means 5 bolt holes with 4-1/2" measured to a point halfway between the opposite bolt holes.)
On wheels with an even number of bolt holes, measure from the center of one bolt hole to the center of the hole directly across from it. (Example: "8 on 6-1/2" means 8 bolt holes with 6-1/2" from the center of one hole to the center of another on the opposite side.)
Measuring the distance from the center of one bolt hole on the wheel to the center of a bolt hole right next to it can also help to determine the bolt pattern.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi, everybody. Andy here with etrailer.com. Let's take a brief look together at this Dexstar Black Steel Spoke Trailer Wheel. Now this sturdy steel wheel with this eight spoke pattern in a glossy black powder coat finish is made here in the USA, and it does meet the Department of Transportation specifications. Now, this wheel has excellent corrosion resistance with the black powder coat finish over E-coat primer, and bringing this back around here, the dimensions of this rim, beginning with the diameter measuring bead seat to bead seat is 16 inches, and then the width, again, measuring bead seat to bead seat is six inches, and our bolt pattern is eight on six and a half inches. And in case you don't know, the first number in the bolt pattern is the number of bolt holes, and the second number is the diameter in inches of the circle on which our bolt holes sit.
So to determine the bolt circle diameter on wheels with an even number of bolt holes as we have here, you're simply going to measure from the center of one bolt hole to the center of the hole directly across from it. Now the wheel stud size is a half an inch by 20, and or nine 16 of an inch by 18. This wheel has a capacity of 3,750 pounds. The center cap is sold separately, but if you decide to pick one up, you would just need to make sure that it fits the pilot diameter of 4.9 inches. Well, that's gonna wrap up our brief look today.
I do hope that our time together was helpful for you. Again, my name is Andy. Thank you for joining me.
The TechLiner is a great product. It fit perfectly and looks awesome. You do need to let it sit in the sun for a couple hours to flatten out. This liner does velcro to your truck bed and may be a hassle if you feel a need to remove it for cleaning very often.
I purchased the tailgate protector. The material is soft and pliable. Unfortunately,the plastic washers that come with it are too small and therefore soon after installation, the protector peeled away from the tailgate at the top where it uses the washers to keep it in place. I ended up using some larger diameter washers to keep it secure. It fits well, and now does a great job of protecting my tailgate.
We received this item in a damaged box that was taped up on one end and busted open on the other end with the mat dirty and warped hanging out of the box. I don't know who to blame the damage on but we are not happy with a damaged product. It is dirty and looks like it may have been used and placed back in the box. I'm expecting this problem to be corrected.
Installation was quick and easy. It fit well and appears to be durable.
Was easy to install. Secured by factory bolts in tailgate. Looks nice no issues.
Up until about a week ago, the bed liner was working just fine, but then the adhesive holding several of the Velcro strips failed or wore out, and the liner caught air and pulled away from the rest of the Velcro and flew out of the bed. I had to pull over to retrieve it from the roadway. I've tried applying some more adhesive, but it still gets air under it, so I had to remove it completely.
Overall the bed liner was easy to install, the fact that it was designed to fit the bed of my specific truck and had a good fit and finish was important to me.
Another nice attribute is that the liner extends up the walls of the bed and does not simply end at the bottom of the bed. This helps keep snow and water and debris away from the bed itself.
The service I received from etrailer was above and beyond and exceeded my expectations.
Jena called me to update me on a change to my order, then followed up twice to let me know the item had shipped.
Highly recommend etrailer !!
Stays in place,makes loading heave things much better because it protects the tail gate.Easy to clean up.
Could easily be made better. The material is great but they could improve the interface with the upper lip of the tailgate and include MORE hook and loop. Also, even though it's fairly obvious, they don't mention using the shoulder washers when screwing it down.
This product will not install on a tailgate that has a spray on bed liner applied. The mat will not fit under the supplied clips. I drilled out all the holes and just used the existing tailgate hardware to attach it. Poor design by WeatherTech. I recommend etrailer to not carry this product.
It’s very light duty and difficult to clip in. Clips get caught up on any cargo your sliding out .
It looks nice new but not very functional if you use your truck bed.
The liner is thinner than expected.
It was a perfect fit. I did need to lift the plastic end of the tail-gate, then drill holes for where the tabs go through, thus making the strip they send along unnecessary. I'm thrilled with the way it looks.
Tailgate liner was thinner and more flexible than I anticipated, but the material seems tough. It has held up well to heavy use.
La verdad me gustaría regresarlo pero ya lo corté para acomodarlo No vale$ lo que cuesta. [Truthfully I'd like to return it but I already cut it to fit. Not worth the cost]
The Bed Mat is 100% durable in my experience and I re ommend it
I pretty much trust everything Weather Tech, but this product missed the mark. It was EXTREMELY difficult to install. It uses a long plastic "C" clip along the upper edge of the tailgate to hold down the mat. You're suppose to install the clip and then slide the mat in from one end, even with lube it wouldn't slide in. I've been working on my own cars for 50 years. It took me quite a while to get the mat into the "C" clip. Then you have to move it back and forth some to line up the screw holes that are reused in the tailgate.
The product does what it's suppose to, protects tailgate from scratches and dings. Looks good and is durable overall. One thing that could be better is the trim/attachment strip at the top. It is a harder plastic that can be caught when sliding something out and gets chipped and broken. Overall the product works as intended.
It fits in the truck box of my 2021 Ford F-150 Power Boost perfectly! I had to trim a little piece off around the power outlets.
It is a good product and does what it is supposed to - protect your tailgate. A couple of things that I noted, though, and they may or may not apply to you. The first is that it is impacted a lot by direct sunlight - meaning it expands and contracts a bit more than I would have expected.
The other is that I use trail seal for my tailgate for the times I am using a tonneau cover. This product doesn't lie quite flat at the bottom of the tailgate and would push the trail seal away. This is resolved by trimming the bottom inch of the mat.
I’ve used Weather Tech products for years, they are terrific. .
Fast service, excellent quality product, easy instructions and fits perfectly!!!
I’m disappointed that the holes for screwing the liner down are to big and the screws go right through them . I will have to get washers to hold it down .
My opinion it’s too flimsy.it doesn’t lay flat in the closed position at the top of tail gate. Needs to be more rigid I
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.