5th Airborne Premium 5th Wheel Air Ride King Pin with Sidewinder - No Turret - 16,000 lbs
(98 reviews)
Price: $1,556.29
In Stock
5th Airborne Premium 5th Wheel Air Ride King Pin with Sidewinder - No Turret - 16,000 lbs
Item # 5AS16K
Retail:$2,840.37
Our Price: $1,556.29
You Save: $1,284.08
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (98)
- Q & A (0)
- Photos
- Used (2)
Reese Fifth Wheel King Pin - 5AS16K
- 16000 lbs GTW
- Upgraded Pin Box
- Reese
- Absorbs Road Shock and Reduces Chucking
- Provides Turning Clearance
- No Turret
Connect the turret portion (sold separately) of the sidewinder to this arm assembly to create a complete 5th Airborne sidewinder, which will enable you to easily make up to 90-degree turns. The built-in air bag both cushions and supports your load.
Features:
- 5th-Wheel trailer's pivot point is moved an extra 22" toward the rear of your tow vehicle so that you can easily make 90-degree turns, even with a short-bed pickup truck
- Rotating turret (ST100, ST200, ST300, ST400 or ST500 - sold separately) required
- No need to get out of your truck, throw a switch, push a button or mount a 5th-wheel slider
- Trailer tracks more closely to the truck for better driveability
- Fully enclosed, custom-tuned air spring in air ride trailer coupler - cushions and absorbs shock
- Reduces longitudinal shock (chucking) by nearly 60 percent
- Decreases vertical shock by 44 percent
- Relieves stress on coach frame
- Reduces vibration inside coach, protecting its contents
- Air bag can be repositioned with 2 easy-to-access screws to better support varying loads
- Move forward for light tongue weights
- Move backward for heavy tongue weights
- King pin connects to standard 5th-wheel trailer hitch and allows easy hookup and disconnect at any angle
- 1-Piece, streamlined construction
- C-Channel design of sidewinder provides more stability and strength than standard pin box
- Able to support heavier loads
Specs:
- Capacity: 16,000 lbs
- Clearance: see formula below to ensure proper clearance
- 3-Year limited warranty
Clearance Formula
Use the formula below to ensure that there will be enough space between your truck cab and trailer when you are executing a 90-degree turn with the 5th Airborne sidewinder installed.
(A + B) - C = Clearance
A = Distance from center of 5th-wheel hitch jaw to truck cab in inches
B = Length of sidewinder arm in inches (22")
C = Width of trailer in inches divided by 2
For example:
If you are using the 16,000-lb 5th Airborne sidewinder, then B = 22"
If the distance from the center of your hitch to your truck's cab is 36", then A = 36"
And, if your fifth-wheel trailer is 102" wide, then C = 51"
102/2 = 51
Therefore,
(36 + 22) - 51 = 7" of clearance
Reese Elite Airborne Sidewinder
5AS16K Fifth Airborne Sidewinder Arm Assembly without Turret
Installation Details
California residents: click here
Customer Satisfaction Score:
86% were satisfied with this product
14% of customers were not satisfied
- Wrong item was ordered
Customer Reviews
5th Airborne Premium 5th Wheel Air Ride King Pin with Sidewinder - No Turret - 16,000 lbs - 5AS16K
Average Customer Rating: 4.5 out of 5 stars (98 Customer Reviews)
Connect the turret portion (sold separately) of the sidewinder to this arm assembly to create a complete 5th Airborne sidewinder, which will enable you to easily make up to 90-degree turns. The built-in air bag both cushions and supports your load.by: Peter04/13/2024
The product was a replacement for another one that had a defect issue which the manufacturer dragged their feet to replace. So I went ahead and purchased another as we needed to continue camping. The product is a decent, etrailer is amazing. However if you are looking for warranty follow up you will not get it from the manufacturer which is why it’s a 2 star. Not because of etrailer and their amazing delivery service.
by: Tony08/14/2017
I've had my Elite Airborne Sidewinder for about 6 months now. it's mounted on a 33 ft Jayco and pulled by a 2016 F-150 Lariat with a 5.5 ft box and the Max tow package. Total trailer weight is about 7800 lbs empty and closer to 9-9500 when we are loaded. We have done several short trips (under 200 miles) and one longer one so far from Montreal to Charleston, SC.
I'm nothing short of blown away by this coupler. There is no chucking, and it pulls so smooth you'd hardly think there was a trailer back there. Even my wife has commented that it hardly feels like we're towing. The sidewinder allows 90 degree turns easily and I can back it down a 80 ft driveway easily. I check the air once in a while in the air ride and have yet to check the key but I can back on to it easily. This coupler does exactly what it was advertised to do, and does it extremely well. We've had it out 6 times this year already and have a few more in mind before calling it a season. My thanks to Reese for an amazing coupler and to Pat and etrailer for their help in getting it to me so fast! Great customer service!
by: Brent08/12/2020
I love the Air Ride King Pin with Sidewinder. The air cushion has removed the lag when taking off and stopping as well as smoothing out the trailer movement on rough road. The solid construction has served me well on our recent 2000-mile road trip.
I tow a 12,000 lb fifth wheel with a short bed 3/4 ton truck.
by: Steven11/19/2022
Excellent Item, Very good seller excellent communication and service
by: Charles03/25/2021
The pin box greatly increases the maneuverability of the trailer / truck combination by moving the pivot point back under the front of the trailer rather than in the middle of the hitch in the truck bed. Additionally, the air ride greatly smooths the bumps out on the road and reduces chucking when braking or accelerating. The only reason for not giving 5 stars is that you MUST be perfectly aligned with the pin box in order to attach it to the hitch. Unlike a traditional king pin, this one is modified to have a large steel plate behind it to force the pin box to pivot under the trailer. This means you MUST be perfectly aligned with the pin box to get it to connect to the trailer. Normally, this is not an issue if you are able to back or pull the trailer to the point where the pin box is straight with respect to the trailer. however, often spots require backing in but are not deep enough to straighten the pin box to the trailer. This means that the truck must be backed in at what ever angle the pin box is at to get it to engage in the hitch.
by: Fred10/17/2019
Reese Sidewinder RV hitch for short bed tow vehicles . This model has air bag suspension (replaced the non air suspension model)
Yes this product works good the ride is much less harsh, although the air suspension model is much higher and I did need to lower the fifth wheel hitch to get the trailer front lowered to a safer tow mode . There was initial damage from shipping (the air filling valve stem is installed when shipping and sticks out if and pokes Out of the box and was bent) Spoke to Reese and they took care in suppling a new valve and connections.
by: Hogan Liechty08/09/2015
Got the box in time for my last trip of about 400 mi. Round trip.
I am replacing a plain sidewinder which is a great improvement over a sliding hitch- mainly because I am able to remove my Reese titan hitch myself without hurting my back. My last hitch slid automatically but weighted a ton.
The box had come open when it arrived, it appears that the packing staples had pulled out. I installed it myself without a great degree if difficulty and discovered the top wear ring was not included. Luckily I had the one from my regular sidewinder.
Don't know if I did it or it happened in shipping but the air valve was mashed on the end. I struggled getting the cap off and had to file it back round again to get an air nozzle on it. It is very soft brass and probably should be protected better for shipping and handling since it is easily damaged.
I was very disappointed in the performance. I drove a road with expansion joints and wished I had the plain sidewinder back on.
After I got home I moved the airbag and adjusted the air pressure in an attempt to smooth the ride. I haven't given it a fair trial yet with the new adjustments.
Sure seems like a lot of money for no significant improvement at this point.
by: Christian04/10/2022
I would have left 5 stars, but the package arrived just about destroyed and the pin box was significantly scratched and the air valve was bent and had to be replaced which I did myself. I had to touch up the paint on the frame of my trailer from the old pin box, so i also touched up all the scratches from shipping.
The hitch is absolutely awesome and was exactly what I was looking for to absorb some road shock! Just got back from a 1,700 mile trip and although it took some experimenting along the way to get it just right, it was worth it. Probably going to add a compressor and wireless valve to control the pressure in the cab because weight and air temps require different psi's. When we left Chicago it was 30° and by the time we got to southern Arkansas, it was 75° and had to let the air out 3 times. On our way back, had to add air multiple times.
by: Daren07/07/2015
Installed this in 10 minutes. Super Easy to install, you can do it by yourself if you're strong and have some skills. Having a helping hand doesn't hurt though. Although the custom bed isn't done on my truck, it's time for vacation. I used a new B&W turnover ball and companion 5th wheel hitch and connected my newly (easily) installed Airborn air bagged pin box.... rides like a dream!!!!! I shouldn't have used my other non-air ride pin box for 10 years! This pic shows my test run, usually the car is a boat.
by: Curt E04/10/2019
I really like my new King Pin with airbag and sidewinder and turret. I am not the greatest at backing up but I feel I have better control due to the geometry change. It is much easier to make sharp 90 degree turns. I hated to have to stop and move the slider. I have had to reset the four bolts on top of the turret and the two bolts holding the wedge to 150 pounds. I use a white lithium spray to ensure an easier connection. I am still trying to figure out what pressure I should set the airbag though. I have it set between 60 and 65. The ride is very smooth with very little chucking.
by: Roy J.05/03/2017
Unit arrived in good condition. Was a breeze to install, about a 1 hour job with 2 people including removal of old Tri-Glide. Didn't like the "banging" back and forth with the tri-glide.
The only issue I had was having to drill pilot hole for breakaway switch screw. Non issue! Can't wait to make a haul with it. Alaska here we come!
by: Andy S06/21/2016
am happy with my new pinbox. Installation was very easy with some help, fit perfectly. I had to run a die nut over 2 trunion bolts that were damaged during shipping. I haven't tried towing yet, but so far I am pleased with my purchase. I have enclosed some pictures of my installation.
by: Jimmy04/15/2019
Received my 5th Airborne pin box in 3 days. I didn’t have any help readily available and I couldn’t wait. It was a direct replacement of my old pin box. The guy I was emailing was very helpful and helped me correct my order as I ordered the wrong one and caught my mistake before it processed. He was great to work with as erailer always is. Highly recommend these guys for all your trailering needs.
It was a little aggravating to install alone with some makeshift braces and 2 large screwdrivers to line up holes. Be sure to sand the inside of the frame if any rust or anomalies are present. Other than that, was a simple install and fit as it should. Thank You etrailer!
by: Bob L.08/11/2014
I haven't used the air ride pin box yet, but I will be going on a trip this weekend. Installation was a breeze with the help of my son to place in position. It took about 45 min. to remove the old pin box and install the Airborne. Another 30 min. to secure the electrics and trailer emergency brake switch.
by: faw05/17/2015
The 5th Airborne Air Ride Coupler is very well made with quality welds.
Installing on a 2010 Cyclone 3612 Toy Hauler, I did have to cut about 1/2 inch from the fiberglass at the top front of the Lippert Trailer Mount. This modification provided the 3/8"
vertical movement required to allow the front 3 bolt holes to line up.
Other than the small fiberglass trim, a very clean installation.
by: DMB05/13/2015
This item arrived quickly. There was some rust inside of the mounting cavity that had to be removed before installing the 5th Airborne. You may also experience some swelling from the manufacturer welding up the pin box cavity. Once this is cleaned up, installation is easy.
by: Joe09/06/2022
The pin box was easily installed and works great.When installed the lable with name and specs is partially covered by the mount on the frame.
by: Tim02/21/2021
This hitch is great, no more chucking and it also takes the hard bounce out. Would recommend to anyone. You will need to adjust the pressure in the air bag to suit the weight of your pin. 100% better pull, you wont be sorry.
by: William06/24/2019
I contacted etrailer several times trying to figure out how to fix my problem. Everyone there that I spoke with was very knowledgeable and helpful. They shipped the product right away and I received it a day before expected. I can't say enough about the great people at etrailer. I would definitely recommend them to anyone looking for trailer parts.
by: Keith03/06/2022
Wow...what a difference!
Replaced our pin box with the 5th Airboure and the ride immediately improved. Almost no chucking!
Even my wife noticed how nice and smooth the truck now rides.
by: Frank 09/26/2021
Was looking for a fifth wheel trailer porpoising solution and this helped considerably. It took some time to figure out the right air pressure to put on king pin and air lifts I have on truck to find the right combination. Although I miss the chuck free Motoryde feel, I’ll take a slight chucking vs. my trailer coming apart from bouncing up and down. Much cheaper and convenient solution to others I have seen.
by: Darvin S05/14/2015
Dana at etrailer was the best, order shipped same day and I received it within two days. Installation of the 5th Airborne was very easy and a well built product.
by: Arthur04/01/2020
Very good quality and easy to install. Took a little more than an hour. Helps to have a tractor with forks and a good cordless impact wrench. Other reviews say it works well. Still snow here but can not wait to try it. Have new Bighorn and with factory pinbox it was a rough 200 miles home.
by: Ed K.04/30/2020
I have a 40 foot, 16,000 GVWR fifth wheel towed by a 1 ton, SRW, long bed with Timbrens also purchased from etrailer. The FW came with a Rotaflex kingpin. The kingpin did a good job with chucking, but the overall ride was very rough. I decided to go with the Reese Fifth Airborne.
We went on a 250 mile trip just before installation of the Reese Fifth Airborne. My wife likes to knit while riding. There were stretches of the interstate where she would have to stop because the ride was so rough. We happened to go over the same stretch of road after the installation of the Reese Fifth Airborne. She did not have to stop her knitting once. The road doesn't turn smooth as glass with this kingpin, but the jarring is eliminated and turned into a a smooth, more subtle bounce.
There are similar products on the market and other setups that are greatly more expensive. IMO, the Reese Fifth Airborne works very well, is relatively affordable and doesn't detract from the looks of the FW. And, of course, purchasing from etrailer is great.
by: Jim10/06/2021
At this time I’m going to give it 3 stars. It was damaged in shipping. etrailer is great and they said it won’t hurt anything. I’m going to put it on and give it a go and maybe come back and edit the review
25
97
Show More Reviews
See what our Experts say about this Reese Fifth Wheel King Pin
- 5th Wheel Trailer Hitch and Installation Kit for a 2015 Ford F-150 with 5-1/2 Foot BedI have an excellent recommendation for your 2015 Ford F-150 with the 5-1/2 foot bed. You can use the Demco 13K HiJacker, # DM8550040, which has 22-1/2 inches of travel and slides automatically. Using this hitch will prevent you from having to buy both a hitch and a Sidewinder pin box. All you will need, besides the hitch, is an installation kit, # RP50087-58. I also recommend adding an in-bed 7-Way to make hooking up the 5th wheel trailer easier, # 41157.
view full answer... - Safety and Ride Quality When Using a 5th Airborne Sidewinder on a 5th Wheel TrailerA Sidewinder, like # 5AS16K, should be used when a slider trailer hitch does not offer enough clearance to safely make 90 degree turns. It provides 22 inches of clearance, 10 more inches than a round tube slider hitch. Sidewinder arms are designed to work with a rotating turret, like # RP61302. The correct turret depends on the trailer pin box make and model. The use of a Sidewinder will put some extra stress on the trailer frame. You will need to contact the trailer manufacturer to determine...
view full answer... - Comparing Sidewinder Repair Kits # RP86005 and # RP94316Repair kit # RP94316 is designed for 5th Airborne Sidewinders whereas # RP86005 is for 16k and 19k Sidewinders only, not the air ride models. The kits are very similar though because a lot of the parts are the same or similar. But I advise using the kit for the type of Sidewinder you have to ensure compatibility.
view full answer... - Recommend Pin Box Extension For Crossroads Paradise 30 Ft Travel TrailerIf you are using a fixed position fifth-wheel trailer hitch, you will want a Sidewinder King Pin. A Sidewinder moves the pivot point back 22 inches to provide additional clearance needed when making tight turns. To determine which Sidewinder you will need, you will need to match up the make and model number of your existing pin box (see FAQ). All of the Sidewinder arms measure 22 inches. To determine the length of your existing pin box, you will measure from the center of the king pin...
view full answer... - Should There be Ridge on Bottom of 5th Airborne Premium 5AS16KThank you for the purchase, and yes there is supposed to be a ridge at the bottom of the 5th Airborne Premium 5th Wheel Air Ride King Pin with Sidewinder - No Turret # 5AS16K. If you take a look at the photo I have added, you can see that ridge which does not allow the wedge to sit completely flat, which is normal.
view full answer...
- Can Reese Sidewinder Be Used to Prevent Hitting 2018 Ram 2500 Ram Boxes on SideThe 16K 5th Airborne Premium 5th Wheel Air Ride King Pin with Sidewinder # 5AS16K can definitely be paired with the 18K B&W Patriot # BWRVK3255 on your 2018 Ram 2500 to prevent the pin box from making contact with your Ram Boxes, but you'll also need the following parts: - Rotating Turret RP61300 - B&W Custom Wedge # SWW-06 The turret installs on the wing plates off your 5th wheel trailer and then connects to the rest of the Sidewinder pin box, and the wedge is needed since the B&W...
view full answer...
- 5th Airborne Sidewinder for Fifth Wheel Towed by 2012 Dodge Ram Quad CabIf your Ram has the 5-1/2 foot bed, the Sidewinder would be your only alternative to possibly gain enough clearance for sharp turns. To determine if you will be able to make 90 degree turns while using the Sidewinder, take a look at the clearance formula on the Sidewinder FAQ page I have linked you to. You will need to measure the distance between your hitch jaw and the rear of your cab. Add 22 inches (length of Sidewinder arm) to this measurement. From this sum, subtract half the width...
view full answer... - Sidewinder Recommendation for a 2006 Ford F250 with a Short Bed Towing a 5th WheelI believe I have a solution for you. A Sidewinder pin box will give you an additional 22 inches of clearance and should give you plenty of clearance for you to make a 90 degree turn with your 2006 Ford F250 Super Duty and 26 foot Holiday Rambler Alumascape 5th Wheel Hitch. Check out the FAQ article I attached on Sidewinders for you to check out. In order to pick out the right Sidewinder you will need to know which model pin box is currently on your trailer. Once you have that information...
view full answer... - Can I Swap my 5th Airborne From a 2018 Jayco to a 2020 Keystone Montana H/CAs long as there is a turret to match the pin box on your new 2020 Keystone Montana H/C 330rl, you will be able to use your # 5AS16K on the new trailer. You'll need to know which model pin box is on the new 5th wheel, first. As an example, the Rotating Turret for 5th Airborne and Sidewinder 5th Wheel King Pins # RP61300 will allow you to connect the # 5AS16K to your new 5th wheel if you have one of the following pinboxes: Fabex 663 and 665, Lippert Components 1621, 1621HD, and 0719, and...
view full answer... - Parts Needed to Convert 16K Reese Sidewinder to 5th Airborne Cushioned SidewinderConverting a standard Sidewinder pivoting 5th wheel pin box like # RP34FR to an air-cushioned 5th Airborne type is possible using part # 5AS16K. This kit includes all required hardware. Please refer to the linked videos for more.
view full answer... - 2023 Keystone Cougar 368MBI Parts Needed for Pin Box Upgrade to Reese SidewinderYes, the 16K 5th Airborne Premium 5th Wheel Air Ride King Pin with Sidewinder # 5AS16K will be perfect for your 14K 2023 Keystone Cougar 368MBI. Please note you also need the rotating turret part RP61300. This is currently unavailable so you'll want to search elsewhere to see if you can pick up this specific part even if it's used.
view full answer... - Can Sidewinder Pin Box for Lippert 1621 be Upgraded to 5th Airborne Cushioned ModelThe Reese Sidewinder pin box # RP34FR that bolts on in place of your Lippert 1621 can indeed be later upgraded to a 5th Airborne air-ride pin box. The item you will add to the existing turret assembly is # 5AS16K that you referenced. We confirmed compatibility with Reese.
view full answer... - Can Sidewinder RP61410 be Upgraded to 5th Airborne Cushioned SidewinderYes, if you wanted to upgrade your Reese Sidewinder part RP61410 to be a cushioned 5th Airborne Sidewinder you'd be able to do so with just the part # 5AS16K that you mentioned.
view full answer... - Does 5th Airborne Premium 5th Wheel Air Ride Fit Sidewinder Turret SW16KYes, the turret from your Sidewinder SW16K is indeed compatible with the 5th Airborne Sidewinder that does not have a turret, which is the following part number: - 5th Airborne Premium 5th Wheel Air Ride King Pin with Sidewinder - No Turret # 5AS16K The SW16K is just the Sidewinder arm and uses the same turret as the 5th Airborne # 5AS16K which is why you can easily change over the the 5th Airborne. This will be a superb upgrade for a much more comfortable ride due to its air spring that...
view full answer... - Is the B&W Companion OEM 5th Wheel Hitch Compatible With Sidewinder Pin BoxesYes, the B&W Companion OEM 5th-Wheel Hitch for Ford Super Duty Prep Package # BWRVK3300 is compatible with sidewinder pin boxes like your # 5AS16K. This hitch uses four attachment points to connect to the puck system in your 2020 Ford F-250 Super Duty's bed. You'll also need the 5th Airborne Custom Wedge for B&W Fifth Wheels Item # SWW-06 to prevent the king pin of your pin box from pivoting in the jaws of your hitch. This hitch has 1" thick dual jaws provide 360-degree jaw-to-king-pin...
view full answer... - Solution to Fix Jerking/Chucking of Fifth Wheel Trailer with Reese Revolution Pin BoxReese Revolution/Sidewinder pin boxes generally aren't too prone to chucking and noise but when this does happen what typically is the problem is the fifth wheel hitch not having a tight enough jaw to hold the trailer tight and prevent the movement associated with the chucking. I don't know what hitch you have now but the B and W Patriot part # BWRVK3200 holds the king pin very tightly and would eliminate the jerking you described. Then for a custom wedge to fit it tightly to your Revolution...
view full answer... - Replacement Air Ride King Pin for Sidewinder Upgrade from Non-Air Ride ModelThe 5th Airborne Premium 5th Wheel Air Ride King Pin with Sidewinder - No Turret - 16,000 lbs # 5AS16K will be compatible with the Rotating Turret for 5th Airborne and Sidewinder 5th Wheel King Pins # RP61300 as it replaced the ST200 model. Using the Air Ride # 5AS16K you will be able to reuse the turret on your Sidewinder 5th Wheel King Pin with Rotating Turret - 16,000 lbs # RP34FR and upgrade to the air ride suspension you are seeking.
view full answer... - Tips for Fitting the 5th Airborne Sidewinder Standard Arm Into the Rotating TurretI actually had the pleasure of fitting these two components together once and found that the fit is very tight. Most important thing to do is use a liberal amount of white lithium grease like part # L11354. I found that once you start the # 5AS16K into the # ST400 the easiest way to make it slide all the way in is to flip the assembly upside down, put blocks underneath the side that's unsupported so that its sits level, and then use a block and hammer to drive the pieces together.
view full answer... - Sidewinder Pin Box for 2022 Wildwood Heritage Glen 5th Wheel The ST200 turret for the # 5AS16K has been discontinued. You may be able to find it still but I wasn't able to when I ran a quick search. At this time, the only Sidewinder we offer that fits the 1621 is the # RP34FR. Also, you aren't hearing from Reese because they're owned by First Brands now. Ever since this change the wait times on the phone are extremely long and many of their parts are gone or on indefinite backorder. The # RP34FR will help with clearance but it won't do anything...
view full answer... - Reese 5th Airborne Premium Pin Box Service Kit AvailabilityHey David! What you're looking for is the 86005 Service Kit which was discontinued a few years ago. You might be able to find one elsewhere online but since these have been gone for a while it will be pretty difficult. I recommend reaching out to Reese directly to get their help with this since they were the ones to discontinue it - https://www.reeseprod.com/ContactUs
view full answer... - What Hardware Is Needed To Lockout The Reese Sidewinder Rotating Pin BoxWe don't have the lockout bolts for your 5th Airborne Premium 5th Wheel Air Ride King Pin with Sidewinder # 5AS16K, however you just need (2) 3/4" x 5 1/2" grade 5 bolts which you can just get at any local hardware store.
view full answer... - Proper Lubrication of Sidewinder Arm # 5AS16K Wear Plate and Pivot PinMy contact at Reese said that the 3rd step in the maintenance process of the 5th Airborne Sidewinder Standard Arm with King Pin # 5AS16K involves taking cleaning and lubricating with White Lithium Grease, like part # L11354, the big square wear disc (or plate) and the round disc that is under the cap.
view full answer... - How To Clean And Lubricate The Wear Plate On A Reese Sidewinder King Pin Part # 5AS16KPer the instructions for the Reese 5th Airborne Sidewinder Standard Arm with King Pin part # 5AS16K, in order to clean and lubricate the wear plate, you must first remove the turret. This can be done by removing the 4 5/8" cap bolts from the top of the pivot arm followed by the 2 3/4" convertible bolts located on the bottom side of the king pin. Once done, you will have to use a pry bar to remove the sleeve around the pivot arm, be careful not to scrape or nick the pivot arm upon disassembly....
view full answer... - Can Reese Sidewinder Pin Box # RP61450 Be Upgraded to 5th Airborne Air-Ride Pin BoxThe Reese Sidewinder pin box # RP61450 that bolts on in place of your Venture pin box (either model CJ13515, CJ13517 or CJ20517) can indeed be later upgraded to a 5th Airborne air-ride pin box. The item you will add to the existing turret assembly is # 5AS16K. I confirmed compatibility with my technical contact at Reese.
view full answer...
Do you have a question about this Fifth Wheel King Pin?
Used Items Available
Condition: Missing Parts
Notes: Unit is missing hardware and has some gouges on it, otherwise fine.
Condition: Badly Dinged
Notes: Unit is slightly dented on one front corner.
Info for this part was:
Video by:
Andrew K
Video by:
Zach D
Written by:
Lindsey S
Expert Research:
Michael H
Expert Research:
Jameson C
Updated by:
Laura H
Updated by:
Wilson B
Updated by:
Alexander C
Updated by:
Jenny M
Updated by:
Isabelle B
Video Edited:
Dustin K
Installed by:
Randy B
Test Fit:
David F
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Steven C.
11/19/2023
Fantastic!