4" Tall x 27-1/2" long ramps attach to a platform or lift to load your vehicle for service. 3" notch supports existing platform or lift ramp. Ramp incline creates an 8.8 degree angle of approach. Fit tires up to 12" wide.
Features:
Specs:
Race Ramps Service Rack Ramps attach to a platform or lift to safely load your vehicle onto a service rack. Simply place the existing platform or lift ramp on the 3" notch to create a smooth transition surface. The ramps have an 8.8 degree angle of approach, which allows you to load a low-ground-clearance vehicle without worrying about scraping its front end.
These ramps are made of ultra-strong, solid core, high-density EPS foam that won't crack or bounce. Each ramp supports 1,500 lbs - giving you a total weight capacity of 3,000 lbs for lifting a vehicle for service. The ramps are lightweight, weighing no more than 4 pounds per ramp, so you can transport and store them with ease.
The ramps are covered with a textured coating and are flat on one side. This keeps them from skidding when you drive up on them. The coating is a hybrid polyurea compound that is resistant to water and other automotive chemicals commonly found around the garage. And although this coating is durable, it will not scratch, mark, or scrape your garage floor or the ground.
A built-in handle on each ramp makes maneuvering them easier than heavier steel or aluminum ramps. The ramps can also hang vertically to free up storage space in your trailer or garage.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello everybody, this is Jeff at etrailer.com. Today we're gonna take a look at the Race Ramps service rack ramps with the four-inch lift. It is for a quantity of two ramps. Now these are four-inch tall ramps that'll attach to a platform or a lift to safely load your vehicle onto a service rack or a trailer. Has the three-inch notch right here you can see. And that's on one end, it'll support your existing platform or lift ramp.
Just place the existing platform or lift ramp on that three-inch notch and it lets you drive right up onto the trailer or onto the service rack. If you notice these ramps will have an 8.8 degree angle of approach which allows you to load a low ground clearance vehicle without worrying about scraping its front end. It will fit tires up to 12 inches wide. And, these are lightweight ramps. They're very easy to use, transport and store.
You can see they have a nice handle on 'em to carry around and the weight on 'em is only about four pounds per ramp. They are an ultra-strong high density EPS foam construction, ensures durability and stability. It's a solid core foam so it won't bounce or crack. And if you're noticed on the back of each ramp, it does have the weight capacity listed which is 1500 pounds per ramp. So for both of these, it's 3000 pounds.
Now the ramps are covered with a textured coating and they are flat on one side. This keeps them from skidding when you drive up on them. The coating itself, I am gonna zoom in a little bit closer try to give you a good shot of it but it is a hybrid polyuria compound that is resistant to water and other automotive chemicals commonly found around the garage. Even though this coating is durable, it will not scratch, mark or scrape your garage floor or the ground. Now these parts are made in the USA.
As we mentioned, it is for a quantity of two ramps. Application is for vehicles with tires up to 12 inches wide. We mentioned the angle of approach on these, it's gonna be about 8.8 degrees. And the last thing we're gonna do is just give you the dimensions on it. The width, 14 inches wide. Overall length from one end to the other, it's gonna be 27 and a half inches long. And then, the height at the tallest point which is right here, it's gonna be right at four inches tall. But that should do it for the review on the Race Ramps service rack ramps with a four-inch lift for a quantity of two.
Average Customer Rating: 4.2 out of 5 stars (6 Customer Reviews)
4" Tall x 27-1/2" long ramps attach to a platform or lift to load your vehicle for service. 3" notch supports existing platform or lift ramp. Ramp incline creates an 8.8 degree angle of approach. Fit tires up to 12" wide.The ramps are exactly what we needed. They are sturdy and fit our trailer ramp perfectly.
I'm glad a friend told me about etrailer , great site with the Top products.
FAST Delivery
These ramps will work perfectly to allow my cars low splitter to easily drive up on the ramp. Ramps are made of a material that should hold up quite well.
Poor quality and it took 2 months to get delivery!!!! Never again
Do you have a question about this Car Ramp?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.