Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there.
Features:
If you're looking for the best tie-downs for your camper, frame-mounted is the way to go. The frame is the most solid part of your entire vehicle, so it just makes sense to attach your camper to something that's not going to warp, bend, or twist. Even more importantly, the camper's center of gravity will sit lower and its weight will be spread across the entire bed. This avoids a top-heavy load perched on top of your bed rails that's liable to sway and get pushed around by crosswinds. The camper's not going to shift or slide around while you drive; it's going to stay put, and your truck is going to handle just like it does without a camper.
Quick Tip: If you have a plastic or spray-in bed liner, it's important that you use a rubber mat under the camper to eliminate any sliding or bouncing.
Frame-mounted tie-downs are also a great pick for preserving your truck's good looks. The brackets install on the frame, tucked nearly flush with the underside of the vehicle. Remove the arms from the brackets when you're not hauling your camper, and the brackets will be barely visible.
Completely custom to your vehicle, the tie-downs attach to exisiting holes in your frame so that there's little to no drilling and no need for any modifications. Because they're custom, you'll want to use our in-house application guide to make sure you get the exact right model. The tie-downs you need might be different depending on what type of hitch or other accessories you have.
Once the tie-downs are installed, use a set of turnbuckles (sold separately) to secure the camper to the tie-downs. The shank on each arm has 2 pin holes so you can choose how far out they extend, that way the turnbuckles can reach the anchors on your camper without making contact with your truck. Tighten the turnbuckles to the correct level of tension (not too tight!).
Make sure the anchor points are offset from the tie-downs instead of lined up with them so that they will hold your camper from multiple angles. This is important for keeping your camper from shifting. Two holes in the attachment plate of the tie-downs let you find the best angle for you camper anchors.
Average Customer Rating: 4.7 out of 5 stars (1504 Customer Reviews)
Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there.Product arrived 10/17/16 as indicated. Will install item my self. Guidelines are clear therefore should be no problem. Shipping time was however longer then expected due to the fact that the item was not on shelf and needed to be ordered. This might be due to the fact that there are probably not that many request for tie-downs which fit the Toyota Tundra Trucks.
The front tie down mounts did not fit my 2008 Toyota Tundra SR5 5.7 L V8.The problem is that the bump stops attached to the rear cab mount bolts are in the way. That is something that cannot be removed permanently to accomodate the tie downs. The arm that bolts higher on the frame needs to be bent at a greater angle to fit both the frame and the cab Mount bushing.The rear fit perfectly.
Second purchase of these torklifts from etrailer. As always, excellent service and super fast shipping. Tie downs are for a 13 Tundra, these mount a lot easier than my Ram 2500.
Fast shipping, quality product, simple installation
Easy install. A impact and a 19mm wrench made quick work of this job, overall about 10min per side with OEM hitch
Easy to install. Good fit
Works great. Fits truck. Fast free shipping
A little tougher to install than the front ones but not too bad. Torklift tie downs are very well made, tried he bumper attached one but I guess bumpers aren't what they used to be I saw bending at the tie down after one trip. So bought these. Entrailer as usual priced well and fast shipping.
Tommy C recommended the TorkLift Camper Tie-Downs. The Instructions are great and very easy to follow. They supply some cool wire helpers to hold bolts in the frame for you. All went very smoothly and a very secure. I love how solid the Camper feels on the truck.
Got the tie-downs today. Shipped quickly. There is an extrusion ridge on the inside of the square tubing my hitch was made from. I had to file that out. Once done, everything slipped together like an Erector-Set project. Whole thing took 20 minutes. Very pleased.
Easy to install. Took less than an hour with no helper. They are very sturdy and I expect them to last.
2020 RAM 3500 with OEM hitch.
The package arrived very quickly and intact. I have a 2020 Ford F250 SD Lariat short bed with a factory hitch. The tie-downs were really easy to install although the hitch adapter plate (see attached photo) which is supposed to attach to the end of the tie-down would not fit inside the tubing on my factory installed hitch so I installed without it and it is tight and snug
Poor packaging, missing parts and showed up looking used from being beaten in shipping.
The drivers rear didn't get built correctly. the hole to put the tie done is missing. I had to drill a hole into the tie down so I could use it. Didn't notice the problem until I went to put the camper on my pickup. The other three are fine.
The rear tie downs do not extend out far enough to avoid the dully rear fender and has damaged the paint on the fender.
My brother installed these and he used air tools. The brackets fit perfectly. The instructions were thorough. They bolted right in and the only delay was the disconnect/reconnect of the e-brake cable to install the driver's side bracket (2019 RAM 3500). After all the parts were laid out, he installed all 4 brackets in an hour.
He commented many times on the weight, high quality and PERFECT FIT of these brackets. These are worth the price and made in the USA.
I bought this when my previous belly bar and rear tie-down bent badly when our truck slid off the road into a steep ditch and our camper nearly tipped sideways off our truck. This product is a bit better then my old set up, but I expected something much better for this very high price. It wasn't too tough to install, despite the poorly written instructions. Also, the kit did not include a bolt fisher for the 7/16 bolt. The bolt fisher supplied was for a 1/2 inch bolt. Fortunately I had the correct bolt fisher from a previous project. I am also disappointed that the tie down hole has a slot cut in it which seems would significantly weaken it. I am not optimistic that the tie-down point will not bend or break if we have a similar significant side load such as when we slid into the ditch. I will probably weld the slot in the tie-down point shut to strengthen it.
The Superhitch is an amazing product. Had a couple now. Expensive but you get what you pay for. Purchasing from E-trailer is very easy and they delivered the product quickly.
Product was easy enough to install, works as designed, very happy. Shipping boxes continue to be an issue, not up to the job!
Torklift tie downs work great!
Frame mounted tie downs that attach to the reciever. No holes to drill!
I think it is a great product but expensive. In retrospect I could not do what I wanted with the truck and hitch so I spent the money needlessly. Not any fault of your company. I would have been just as well to leave the stock OEM and not spent the money anyway. Live and learn.
Do you have a question about this Camper Tie-Down?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Helmut F.
10/19/2017
After I installed the tie-down on my Tundra on my own, thanks to the clear and easy to understand instructions I drove many miles on Fwys, mountain roads etc. . The best of all, I am clearing the back bumper the way it should. The springs are fantastic. I feel save to have the ForkLift on my camper!!!! Thanks for a great product.