Summer Starts Here - Save up to 70%
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Awning clamps easily attach to the arms on your RV's awning and clamp tightly around the awning fabric to prevent costly rips and cut down on noise caused by the fabric flapping in the wind. Durable plastic construction.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today, we're going to be taking a look at the Valterra Awning Saver Clamps. They're available in white with part number A10253 and in gray, part number A10252. Enjoy your camping vacations a lot more without the worry of your awning tearing and the annoying flapping that may occur. The awning clamps easily attach to your RV's awning frame. They're going to work with most awning frames. They're sold in a pair.
Pick up as many as you'd like to further secure your awning. The awning clamps feature dimples on each pad to interlock for a tight hold on the awning fabric. They're made out of a durable plastic construction. Now that we've gone over the features, I'll go ahead and show you how to get them set up. I've already got my awning out an in place where I want it with one awning saver clamp installed. Let's go ahead and do the next one.
Here you can see there's quite a bit of flapping in our awning. Let's go ahead and get the clamp installed. You want to make sure the hardware is out of our clamps, and we want to make sure and sandwich the awning fabric between the rough side. We've got a couple different options that we can use to mount our clamps. We're going to use the furthest out. We'll set it in place onto our awning frame, and we'll take the bottom one and do just the same.
Then I'm just going to hold it together, and then run my hardware. We've got two different holes to run our hardware through. We're going to go with the one furthest from our awning. We'll drop that down through. We'll make sure it goes through the second clamp.
With my bolt through, I can now let go of the clamp. I'll take my flat washer, put that on bottom, followed by my wingnut. Before I tighten it down all the way, I'm going to pull on my awning to take out the slack, and then tighten it the rest of the way down. There we go. With it in place, as you can see, there's less flapping in our awning, and it's nice and secure. That's going to complete our look at the Valterra Awning Saver Clamps.
Average Customer Rating: 4.7 out of 5 stars (7 Customer Reviews)
Awning clamps easily attach to the arms on your RV's awning and clamp tightly around the awning fabric to prevent costly rips and cut down on noise caused by the fabric flapping in the wind. Durable plastic construction.These clamps look like they'll do the job. Keep the awning from flapping. While I won't be using mine until September, my buddy has some and I can say that they work great.
Product received, have not used it yet.
Sandra
6/5/2020
Great, still working as described, as the should.
Product was early! Thank You
Exactly what I wanted they fit good.
Thank you.
Item came in quickly with no problems
Work great
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Cliff C.
8/19/2018
Update: Recently on a trip to the Uintas, a strong wind came up during a nighttime thunder storm. While our neighbors in the campground were up at zero-dark-thirty rolling up their awnings, ours stayed secure with little to no flapping. I also used some homemade weights to help anchor the awning frame but the clamps kept the awning from snapping in the wind. Great idea!