Fulton Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - Zinc - 1.2K
(653 reviews)
Price: $105.16
In Stock
Fulton Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - Zinc - 1.2K
Item # FTJ120W0301
Retail:$146.78
Our Price: $105.16
You Save: $41.62
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (653)
- Q & A (0)
- Photos
Fulton Trailer Jack - FTJ120W0301
- 1001 - 2000 lbs
- Boat Trailer
- Sidewind Jack
- Swivel Jack
- Leveling Jacks
- Tongue Jacks
- Weld-On
- With Wheel
- Fulton
- 10 Inch Lift
- Steel
Replaces the old Fulton bolt-thru swivel jack on your Jon boat or skiff trailer. Installs on your existing mounting bracket. Premium zinc finish has a 600-hour salt spray rating is ideal for trailers near saltwater.
Features:
- Supports, lifts, and lowers your boat or recreational trailer
- Swings up and down smoothly
- J-bolt handle lets you position jack quickly
- Makes it easy to move your trailer in tight spaces
- Caster turns a full 360 degrees
- Resists rust and corrosion, even in areas with salt
- Premium Z-Max zinc coating has a 600-hour salt spray rating
- Lasts for years thanks to durable steel construction
- Avoids winch posts, tool boxes or other accessories mounted on your trailer
- Sidewind handle lets you crank jack without your hand getting smashed
- Incorporates a grease zerk for easy maintenance
- No need to remove and re-lubricate gears
- Mounts on your existing bolt-thru swivel bracket
- Weld-on bracket (P9012-00 - sold separately) can also be used for mounting
Specs:
- Mounting bracket pin hole spacing: 3" on center
- Lift capacity: 1,200 lbs
- Bracket height:
- Retracted: 13"
- Extended: 23"
- Screw travel : 10"
- Inner tube diameter: 1-3/4
- Outer tube diameter: 2"
- Wheel diameter: 6"
- Clearance: 11" from mounting bracket to top of jack
- Handle swing radius: 7"
- Snap ring pilot hole diameter: 2-1/2"
- Limited 5-year warranty
Quick Tip: Old snap rings can be a pain to remove. Snap ring pliers can make this a lot easier, and you can find them at most local hardware stores. You can also try gripping each end of the snap ring with 2 regular pliers to pry it open and pop it off.
Excellent Corrosion Resistance
The simple truth is that salt can be highly corrosive to metal when exposure lasts for an extended period of time. So, the more you tow around it, the more you need to protect your trailer from it.
The Z-Max zinc finish on this jack offers great corrosion protection, even with occasional use around saltwater, to help ensure that it doesn't end up looking like the one above. Rust-resistant coatings are graded according to a salt spray rating. Basically, this rating shows the amount of time it takes for a material to show signs of corrosion when exposed to pure, continuous salt spray. Traditional zinc plating typically begins to deteriorate after about 100 hours. Dacromet usually lasts for around 300 to 400 hours. Fulton's Z-Max finish lasts for 600 hours in the salt spray test - 30% longer than a standard powder coat finish.
The environment this test creates is much harsher than anything you'll ever experience in your journeys, but it provides a testament to how well this jack resists rust and corrosion.
How to Determine the Lift Capacity You Need in a Jack
A trailer jack lifts your trailer high enough at the tongue to allow you to couple it with your vehicle. Usually, your tongue weight is about 10-15% of your gross trailer weight (GTW). For example, a 10,000-lb trailer has a tongue weight of 1,000 lbs to 1,500 lbs. To raise the tongue of a trailer this size, you'd need a jack that can handle a static load of no less than 1,500 lbs. And, yes, it's okay to have a jack with a weight rating that is higher than your trailer's tongue weight. In fact, a jack with a higher capacity should operate more efficiently, allowing you to spend less time cranking and more time fishing.
TJ120W0301 Fulton Trailer Jack - Swivel - Sidewind - Snap Ring -10" Travel - 1,200 lbs
California residents: click here
Customer Satisfaction Score:
95% were satisfied with this product
5% of customers were not satisfied
- Wrong item was ordered
- Arrived Damaged
- Too difficult to install
Customer Reviews
Fulton Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - Zinc - 1.2K - FTJ120W0301
Average Customer Rating: 4.8 out of 5 stars (653 Customer Reviews)
Replaces the old Fulton bolt-thru swivel jack on your Jon boat or skiff trailer. Installs on your existing mounting bracket. Premium zinc finish has a 600-hour salt spray rating is ideal for trailers near saltwater.by: Aaron 05/16/2024
Spoke with customer service and they suggested this Jack for direct replacement of one on my boat trailer. Jack fit perfect. No issues works great once again thanks ER for always steering me in the right direction.
by: Bob 04/14/2023
courteous,informed customer service.would like to have had some instructions included with product,but that's a small thing.
by: David 05/06/2024
Cammi, very professional, knowledgeable and efficient,
I received the correct part needed in a timely fashion.
I’ve used etrailer for other items in the past and will continue to do so in the future.
by: Darren 02/20/2024
One of the only online retailers with the EXACT unit I needed to replace a broken jack on a 30-year-old ski boat trailer. I was able to re-use the existing mounting plate and didn't have to do any welding.
by: 58retired03/14/2017
Fast shipping. Installed on my trailer quickly. The locking pin was smaller than on my old mount. The jack had the bigger hole needed on the left side. I took the pin off my old jack and installed in the left hole. My mounting bracket has holes all 4 corners so this works great. Great product/service by Etrailer. Will come back again.
58retired
3/14/2018
Still working great. Would buy again if needed.
by: Linda11/25/2023
it was what the product claimed to be...very fast delivery..fit right on the trailer it was made for
by: Johnny03/29/2017
This is a great replacement jack for our boat trailer, a 1999 Triton TR18. Replaced the original perfectly, without having to change the original welded base. Highly recommended. Got a 'before' and 'after' photo to help show what I mean.
Johnny
4/2/2018
It’s working superbly, zero problems. The addition of the grease fitting was a great idea.
by: Mike B.10/31/2012
This is the exact replacement jack that was on my trailer. I couldn't find one locally, but etrailer had it in stock and shipped the same day that I ordered it. They emailed all the information that I needed to track my shipment. It was two business days on the delivery. This is my second purchase from etrailer and all that I can say are great things about them. I would highly recommend etrailer for all your trailer needs.
Mike B.
5/10/2014
After one year, the jack is working great. I would highly recommend this product.
by: Greg C.06/01/2017
This was a replacement jack for my 1990 model boat trailer. Great looking product at a good price. I used the existing mount on the trailer and the jack fit perfectly. Look forward to doing more business with etrailer.
Greg C.
6/1/2018
Jack works fine and is a very good product.
by: Clark07/09/2018
Works great. Didnt have to reweld the backing plate. I was able to use the existing one still on the trailer. Just removed the snap ring and switched out the old with the new.
Clark P.
7/9/2019
Its been great. Plus I havent crunch or bent it yet..
by: Wayne03/16/2020
I've got a JC Tritoon 226 with 6000 lbs. GVWR (Gross vehicle weight rating) and 3500 lbs. Front and Rear GAWR (Gross axle weight rating) trailer. Had to replace the jack because I kept braking the pin turning the gear to pump the jack up. The weight of trailer was more than the jack could handle. Notice the jack had a 500 lb. rating. I been looking for a replacement jack with a welded on plate and snap ring. All I wanted to change was the jack and snap ring. I found the Fulton round with snap ring swivel model FTJ120W0301 with 1200 lbs. rating. Had this new jack installed in 10 minutes and fits just perfect. Could be happier! Great replacement.
by: scott11/02/2021
The Fulton snap ring weld-on swivel jack was an improved version of what has been on my 1999 MFI trailer for the same year Triton TR21. The old jack was becoming very difficult to crank to the appropriate height regardless of lubrication.
Very easy replacement with a pair of snap ring pliers. Of course I didn't have a pair. [hardware store] has an inexpensive pair $xx that work well enough for this single use installation. Could have reused the old snap ring, but went with the new one included with the jack. Might take you longer to hook up to your tow vehicle than replacing the jack.
Full disclosure: The original order arrived two days after the order was placed. Unfortunately, it was filled incorrectly. Mistakes happen, but etrailer went above and beyond to correct the mistake. Would reorder from etrailer without hesitation.
I really appreciate the time etrailer takes to provide product and installation videos.
by: Dennis S.12/10/2013
Just installed the jack on my utility trailer. It had the weld on back plate which made it a piece of cake to do. I had to relocate my spare tire bracket which was no problem. I also installed a hand winch to use if I needed to pull on a lawnmower. The jack came from etrailer right on time. It's not the first time I bought something from them. Great company. My only regret is it was made in China, wish they would try the USA.
by: Bernie 05/12/2024
C-clip snapped right in place
GOOD TO GO
by: Barbara09/02/2023
Was not aware it didn’t come with bracket. Do know what bracket to get. It was loose in a box. I’m assuming it was a return
Brooke M.
9/11/2023
I am sorry to see you are missing a piece! I have already sent your information to our customer service team and they will be reaching out to you about this.
by: Paul 08/26/2023
I have not had my jack installed yet. I thought I might be able to use the existing mounting bracket from my Shelby 5784 jack but it looks like I need to have the old one replaced and have the new mounting bracket welded onto my trailer. Once I get the new one installed, it appears that this will be a great jack.
by: Les03/07/2022
The Jack fit perfectly on my 1999 Triton boat trailer made by MFI. The trailer has the welded plate with a 2 1/2" center. The jack is attached by a snap ring (some call it a 'C' ring). As others have stated, use a decent snap ring plier and replacement is simple. I liked the new snap ring better than the original one so I used the new one. Jack works great!
Les F.
3/10/2023
It has been a year since I bought the trailer jack. It is still working like the day I bought it. Very pleased with my purchase.
by: Kevin 10/05/2023
This Jack has worked great and very happy I replaced it with a unit from etrailer.
by: Gayland09/16/2022
New jack works good This jack is the only one I could find that would replace my old weld on jack I didn’t have to cut off old hardware welded to trailer.
by: Mike O09/10/2018
Product installed easily over existing mount. Big improvement to the smaller jack I had been using. The jack is on my Sylvansport Go utility trailer. Make sure to use 9” snap ring pliers. Took about 10-15 minutes to remove old jack and install new one. Found etrailer great to work with and very professional and customer oriented. The only improvement I would suggest is to more clearly state the mounting diameters.
by: Jim N.06/20/2019
I have a 1997 Eagle boat trailer and I raised the jack up to high and the jack came apart. Since the jack mounting bracket is welded to the trailer I wanted a replacement jack that would mount to the existing bracket. I checked a number of boat related sites with no luck than went to etrailer. I found Fulton jack FTJ12W0301 and I read the reviews and it appeared to be a replacement for old Shelby jack model # 5756A. I ordered the Fulton on Sunday night and it arrived on Thursday afternoon by UPS! You need a good large pair of Snap Ring Pliers and it took about 5 min to install the new jack you get a new snap ring which I used and a mounting bracket which I did not need, the new ring fits fine on the existing mounting bracket. The only thing and the reason I did not give it 5 stars is that the pin that holds the jack in up right or swiveled position is 3/8" diameter and the old Shelby pin is 1/2" so there is a little wobble but should not be a problem, just fortunate to replace the old jack so easily when there was no other way to do it without a lot of work. My F-150 has a trailer ball high of 19" and I jacked the trailer receiver to 24" just did not want to go any higher so I'm good to head to the lake!
by: Kevin11/13/2021
I know it only a trailer jack but it's supposed to be brand new. Here is a picture of all the nicks and imperfections.
Jenny N.
11/16/2021
I will have our customer service team reach out to you.
by: Michael Miranda09/29/2020
Thank you etrailer, delivery couldn’t have been any faster for free ! The dimensions for the mount on to my original welded plate to my bass boat trailer fit perfectly. The snap ring went right into the milled ring . The new 1200 lb jack is 450 more lifting power. So the jack cranks the boat trailer with ease . Thank you
by: Joe T08/23/2023
It’s prefect, works great on my boat trailer “Ellis trailer”. I recommend this product. After one year, it works the same as the first day install.
by: Brian V.01/21/2017
My original jack on my 1997 EZ Loader trailing for a Champion 191DC Elite bass boat.
Did some on-line research and found this site. Was not sure I could even replace it because the plate is welded on the frame, but after looking at some of the videos on this site I figured out which one to order.
Everything went great with the order and shipping was very fast. the follow up emails also showed that they care about their customers.
I did get a snap ring pillars and the job took about 10 minutes.
Thanks,
Brian
25
653
Show More Reviews
See what our Experts say about this Fulton Trailer Jack
- Replacement Snap-On Trailer Jack for Atwood 1,000 lb Snap-On JackThe Fulton Round, Snap-Ring Swivel Marine Jack # FTJ120W0301 will work in place of your 1,000 lb Atwood snap-on jack as long as the bracket that is on the jack matches up with the dimensions in the attached picture. If they don't match up then let me know what your dimensions are and I can help you find something that is compatible. Attached is a review video for you to check out as well.
view full answer...
- Replacement Trailer Jack Recommendation for Shelby # 5856AWe have the Fulton trailer jack part # FTJ120W0301 which we know fits the same trailer mount as the Shelby 5856A that you have so this would be our best option for a solid jack with a very easy install. This jack has a 1,200 lb capacity, a wheel caster, and is a sidewind which I think is easiest style to crank. I attached an install video for this for you to check out as well.
view full answer... - Will a Fulton Trailer Jack Fit the Same Weld On Mount Used by a Shelby JackIt is possible that you can reuse the same mount. It depends on the style of the jack you have and the one you want to replace it with. For example, the Fulton Round, Snap-Ring Swivel Marine Jack, # FTJ120W0301, has a mounting bracket with an inner diameter of 2-1/2 inches. It uses a 3/8 inch pull pin. If it does not match what you have on the trailer, the jack does come with a new weld-on bracket that you can use.
view full answer... - Trailer Jack to Replace Swivel Wesbar Trailer Jack with Wheel CasterI wish we had a rebuild kit for your trailer jack but that's not something that's available due to the age of the jack. The best and most similar solution we have then would be the Fulton trailer jack part # FTJ120W0301 which has a 1,200 lb capacity, swivels like what you have, is a sidewind, and has a wheel caster.
view full answer... - Swivel Jack for a 5-1/2 Inch Tongue on a Ranger Boat TrailerAll of the Fulton bolt-on swivel jacks fit 3x3 to 3x5 frames but none for a 5-1/2 inch frame. You would need to look at weld-on jacks such as # FTJ120W0301. If your Ranger boat trailer has an aluminum frame then it will require a professional with experience in welding steel to aluminum to install the jack.
view full answer... - Replacement Fulton Round, Snap-Ring Swivel Marine Jack # FTJ120W030You don't have to remove the mounting plate if you're wanting to replace just the Fulton Round, Snap-Ring Swivel Marine Jack # FTJ120W0301, but you will get one with the kit so you'll have an extra. We do not sell just the jack only a couple replacement parts. You just need to have a tool to release the snap ring to remove the jack. If you grab another jack # FTJ120W0301 it will come with everything you need to replace and a bit more.
view full answer... - Trailer Jack with Wheel that Fits Same Pipe Mount as Bulldog JackSince Fulton and Bulldog jacks fit the same size snap rings and since Bulldog doesn't offer a similar jack that has a wheel caster your best solution is the Fulton part # FTJ120W0301 which would fit the same snap ring and comes with a wheel caster.
view full answer... - Options For Replacing A Damaged Jack On A Scarab Boat TrailerIt may be possible to replace the internal components and jack itself without have to cut off your original one, but I was unable to find any information as to what brand or model jack was used on your 2019 Scarab trailer, unfortunately. With that said, you will need to contact Scarab with the trailer's VIN to gather this information. They should be able to tell you exactly which jack was used. As an example, if you have a Fulton jack, like the Round, Snap-Ring Swivel Marine Jack # FTJ120W0301,...
view full answer... - Shelby Jack Model 5856A Replacement Recommendation on Jet Ski TrailerWhat we have heard is that the Fulton # FTJ120W0301 does fit the mounting plate of the Shelby Jack 5784 which is what it looks like you have something similar to.
view full answer...
- Replacement Jack Solution for Shelby 5856A that Uses Same MountI recommend replacing it with the Fulton Round, Snap-Ring Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,200 lbs # FTJ120W0301 which will fit your existing jack mount so it will be an exact replacement, and you will actually have a little stronger of a jack as this jack has a 1200lb lift capacity compared to your Shelby jack that had a 1000lb capacity. What that means is that it will be a little easier to jack up and down.
view full answer... - Recommended Boat Trailer Jack To Replace Shelby 5865A That Uses Same Mount On TrailerWe have exactly what you are looking for. I recommend the Fulton Round, Snap-Ring Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,200 lbs # FTJ120W0301 which we have been able to confirm will fit the same jack mount as your discontinued Shelby 5856A Trailer Jack. The # FTJ120W0301 has a 1200lb capacity, a caster, up to 10" of lift, and its zinc finish has a 600 hour salt spray rating so it will hold up perfectly in wet conditions. I included a video of the # FTJ120W0301 being...
view full answer... - Replacement Jack For A Shelby 5856A That Uses The Same Mounting Plate The Fulton Round, Snap-Ring Swivel Marine Jack # FTJ120W0301 will fit the same trailer mount as the Shelby 5856A. The trailer jack has a heavy-gauge steel construction. It has a 600-hour salt spray rating which makes it ideal for marine and recreational use. The jack has a lift capacity of 1,200 pounds. I attached a review video link below.
view full answer... - Recommended Replacement Trailer Jack for 2004 24' Sea Ray Boat TrailerThe profile 2000 mentioned on your 2004 23' Sea Ray Boat Trailer is actually the model of the winch. Based on the picture of the jack, we to not have a jack that is going to be an exact replacement due to the odd fasteners used to mount the jack to the frame. Instead I recommend using the Fulton Round, Snap-Ring Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,200 lbs #FTJ120W0301 and having the included snap-ring mount welded to the frame of the trailer. This will allow you to...
view full answer...
- Fulton Snap-Ring Jack RecommendationThe Fulton Round, Snap-Ring Swivel Marine Jack # FTJ120W0301 that you referenced would be a good choice for you. The zinc coating helps prevent corrosion also. This jack has a 1,200 lb lifting capacity. You will need to be sure that is enough capacity to lift the tongue of your trailer. The # FTJ120W0301 is designed tor snap ring pilot holes with a 2.3 inch diameter. So if you measure the one that is on your trailer and it would be compatible this would bolt right up. Or you could weld...
view full answer... - Replacement Snap-Ring Swivel Jack to Replace Fulton MagnumFor a snap-ring swivel jack to replace your older (unserviceable) Fulton Magnum I suggest the Fulton Snap-Ring Swivel Marine Jack # FTJ120W0301. This side-wind jack offers 10-inches of lift and a 1200-lb capacity. For reference I linked our page for all side-mount jacks with wheels.
view full answer... - Replacement Fulton Snap Ring Jack for 2004 Triton TR 1863 Boat TrailerThe standard outer tube for a trailer jack has 2-1/4" diameter , which is very close to the 2-3/8" you mentioned. You may want to measure the diameter of your outer tube using a caliper like # PTW80157 to make sure you get an accurate reading. Although we don't have a Fulton marine jack with a 2 3/8" outer tube, but we do have something that will work. Fulton Snap Ring Marine Jacks, like # FTJ120W0301 are designed to fit snap ring pilot holes which are 2.313" in diameter. If yours measures...
view full answer... - Do All Fulton Tongue Jacks Mount To The Frame Of A Boat Trailer The Same Way?While there are a few exceptions, the majority of Fulton swivel trailer jacks use either a bolt on or snap ring mount, and will be pretty much the same overall dimensions. If your jack uses a bolt on mount you would want the Fulton XLT Bolt-Thru Swivel Trailer Jack - Bolt On - Sidewind - 12" Lift - 1,500 lbs # F141133 which will bolt directly to your current mount with one bolt in the center as you can see in the included picture. If your jack uses a snap ring to attach you would want...
view full answer...
- Replacement Jack Recommendation for my 2000 Ranger R83 Ranger Trail Single Axle TrailerI believe you are looking for the square mounting plate in that year and the Fulton Bolt-Thru Swivel Marine Jack w/ Caster part # FXP10 will attach to it directly. It is a 10" lift model so no skyscraper but this is common on marine jacks because of the swiveling design giving an automatic drop when rotated down. If for some reason your trailer has been switched to the snap ring attachment type the Fulton Round Snap-Ring Swivel Marine Jack part # FTJ120W0301 is the way to go. Same lift...
view full answer... - Trailer Jack Replacement For a 1997 Ranger Comanche Boat TrailerIt really looks like you have a Fulton Jack like the part # FTJ120W0301 based on the picture you submitted. The jack portion of the picture matches the jack I mentioned but the bracket on the trailer does look slightly different. Does the tube welded to your trailer that the jack mounts to measure 2 inches? If so this would be a match.
view full answer...
- Trailer Jack Recommendation for Trailer with 6 inch Tall Trailer FrameWe have a solution that will work for you, but none of the bolt-on trailer jacks we offer are compatible with a 6 inch tall trailer frame. For a trailer frame of that height, I'd recommend you use a weld-on jack like part # FTJ120W0301. This jack has a 1200 lb capacity, and easily swivels rearward for storage with the pull of a pin.
view full answer... - Trailer Jack with Wheel Recommendation for a Bear Boat TrailerThe Dutton-Lainson Trailer Jack, # DL22300, that you referenced will fit trailer jacks up to 3 inches wide by 5 inches tall with the bolts provided. This jack will be able to fit your 3-1/2 inch wide x 3-1/2 inch tall trailer frame using longer bolts. The mounting bracket on this jack has different holes to accommodate different height trailer frames up to 5 inches. You could also use a weld on style jack like the Fulton Round, Snap-Ring Swivel Jack, # FTJ120W0301. This jack welds on...
view full answer... - Replacement for Dutton-Lainson 203925B 1000 lb Capacity Swivel Trailer JackThe direct replacement for your Dutton-Lainson 203925B jack would be part # DL22560. According to Dutton-Lainson, the jack would indeed be compatible with your existing mounting plate. I've linked to a product demonstration video featuring the # DL22560 jack.
view full answer...
- Do Bulldog and Fulton Trailer Jacks Use Same Snap Ring DimensionsThe Bulldog and Fulton jacks use the same snap ring dimensions like the part # FP908600 which has an inner diameter of 2-5/16 inches. That means the part # FTJ120W0301 will fit on your trailer's mounting bracket that had a Bulldog jack installed on it.
view full answer... - Solution for Installing Trailer Jack on Frame that Measures 6 inches TallWe have a solution that will work for you, but none of the bolt-on trailer jacks we offer are compatible with a 6 inch tall trailer frame. For a trailer frame of that height, I'd recommend you use a weld-on jack like part # FTJ120W0301. This jack has a 1200 lb capacity, and easily swivels rearward for storage with the pull of a pin. A qualified welder in your area would have no problem installing this jack either. Would only take them a matter of minutes. Weld on applications are better...
view full answer...
Do you have a question about this Trailer Jack?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Robert G
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Reno H
Expert Research:
Jameson C
Expert Research:
Adam R
Expert Research:
Jeffrey L
Written by:
Lindsey S
Installed by:
Patrick B
Installed by:
Kathleen M
Video Edited:
Jacob T
Updated by:
Laura H
Updated by:
Wilson B
Updated by:
Alexander C
Updated by:
Hannah L
Updated by:
Isabelle B
Updated by:
Ryan F
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Bob G.
4/15/2024
Fantastic