Pull Pin, Easy Swivel Trailer Jack with 8" Wheel - Sidewind - 1,500 lbs. by Dutton-Lainson
(169 reviews)
Price: $121.73
In Stock
Pull Pin, Easy Swivel Trailer Jack with 8" Wheel - Sidewind - 1,500 lbs. by Dutton-Lainson
Item # DL22800
Retail:$174.54
Our Price: $121.73
You Save: $52.81
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (169)
- Q & A (0)
- Photos
Dutton-Lainson Trailer Jack - DL22800
- 1001 - 2000 lbs
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Sidewind Jack
- Swivel Jack
- Leveling Jacks
- Tongue Jacks
- Bolt-On
- With Wheel
- Dutton-Lainson
- 10 Inch Lift
- Steel
This Dutton-Lainson sidewind swivel jack is a back saver when hitching and unhitching loaded trailers. The heavy-duty D-L tongue jack reduces the effort required to maneuver a trailer into hitching position or to remove the trailer from a vehicle.
Features:
- Easy installation:
- Bolt on mounting
- Can be mounted in a variety of ways on various sizes of trailer tongues
- Bolt on mounting
- Made from heavy-gauge steel for strength and durability
- Enclosed outer tube retards sand and dirt from contacting miter gears and heavy-duty Acme screw
- All mounting hardware included
- Floating miter gears allow for proper clearance and easier operation
- Maximum manueverability from offset swivel caster assembly
- Zinc plated TUFFPLATE finish
- Ergonomic hand grip with textured surface
- Made in the USA
Specs:
- Mounting: 3" x 5" trailer frames
- Overall length: 26-5/8"
- Wheel dimensions: 8" diameter x 2" wide
- Bracket height:
- Retracted: 13"
- Extended: 23"
- Total lift: 10"
- Inner tube diameter: 2"
- Outer tube diameter: 2-1/4"
- Handle radius: 6-1/2"
- Lift capacity: 1,500 lbs
- 3-Year limited warranty
How to Determine the Lift Capacity You Need in a Jack
A trailer jack is designed to lift the tongue of your trailer so you can connect the trailer coupler to your hitch ball. To do this, you'll need a jack with a lift capacity high enough to handle your trailer's tongue weight.
Tongue weight is the amount of weight that your trailer applies to the back of your tow vehicle. Typically, your tongue weight should be 10-15% of your total trailer weight (trailer + cargo). In other words, a 10,000-lb trailer would have a tongue weight between 1,000 lbs and 1,500 lbs. For a trailer this size, you would need a jack with a lift capacity of at least 1,500 lbs.
It's okay to have a jack with a weight rating that is higher than your trailer's tongue weight. In fact, a jack with a higher lift capacity should operate more efficiently, allowing you to spend less time cranking and more time camping.
Trailer and Camper Jack Lift
Every jack offers a certain amount of lift or travel. Screw travel is the distance the jack extends when you crank it (or toggle it to "extend" on an electric model). Some jacks include a drop leg for extra adjustability. On these jacks, you'll see the maximum extension of the drop leg listed in the specs as well. Adding the screw travel and drop leg travel together will give you the total lift. The total lift listed above can help you determine how high this jack will be able to raise your trailer.
22800 Pull Pin, Easy Swivel Trailer Jack with 8" Wheel - Sidewind - 1,500 lbs. by Dutton-Lainson
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- Wrong item was ordered
- Defective
Customer Reviews
Pull Pin, Easy Swivel Trailer Jack with 8" Wheel - Sidewind - 1,500 lbs. by Dutton-Lainson - DL22800
Average Customer Rating: 4.7 out of 5 stars (169 Customer Reviews)
This Dutton-Lainson sidewind swivel jack is a back saver when hitching and unhitching loaded trailers. The heavy-duty D-L tongue jack reduces the effort required to maneuver a trailer into hitching position or to remove the trailer from a vehicle.by: Jon 07/07/2021
First of all, despite the typical delays we're all experiencing these days the people at Etrailer sent updates. Communication is a good thing! I installed the jack on my Shorelander trailer and had to drill out the holes for the lock pin to accomodate the larger diameter pin as I had to use the factory mount on the trailer. Other than that, it mounted nicely and sure makes it easy to move the boat around. Well built jack, no more creaking and flexing!
by: Donna 07/18/2020
This trailer jack is amazing. The turn handle mechanism works so well, very smooth. We really like the ability to turn it sideways so it stores horizontally when in transit. The wheel turns very easily, making positioning painless. We both love that it was made in the USA. Ordering was easy, and shipping was lightning fast. Will be back if we need any more accessories for our trailer.
by: Dennis 09/13/2023
Great service and kept me up to date on the status of my owder
by: Thomas 06/22/2020
Amazing quality, easy to install (20 minutes), works like a charm. This will outlast the trailer!
Installation videos were helpful
Thanks!
by: Steven 03/10/2023
Very happy with quality of the product. Would highly recommend this product. Made better than the original that came on my trailer
. Made in USA
by: Wayne 07/19/2023
Easy to install. Higher weight rating than the OEM
by: Tracy10/11/2018
Not much to say: they had it, they shipped it, I got it, I installed it.
The folks at etrailer are my “go-to” guys (& gals) for almost everything retailer!
Great service!
by: Joe09/23/2022
This Trailer Jack is a solid USA made jack. It is heavy duty and I especially appreciate the large wheel. Paul B. was most helpful with the information I needed and he certainly got the delivery on the move...got it in two days.
by: Dave 04/24/2021
The packaging of this product was in a heavy-duty cardboard which held up well. The appearance and heft of this jack was much better than the Chinese built version I bought a year ago. Immediately after installing this and putting the weight on the jack the boat glided easily on the new, larger wheel. Can't wait to take the boat/trailer out of the garage and enjoy the ease of movement from this new wheeled jack.
by: Brit09/28/2019
Always a great experience buying products from etrailer. The jack was purchased to replace the existing Jack which prematurely broke. The gears stripped out not allowing me to raise or lower the trailer. This new Jack is definitely better quality and the 8 inch wheel gives me better handling in the dirt. Thanks for shipping so fast!
by: Stephen 07/21/2021
Great, easy to install just might be improved a touch with the top bracket hole being a slot versus just a hole so there would be a bit more room to make a tight fit on some odd sized rails (like my vintage camper). BUT easy to install and works great!
by: Bob 04/22/2021
This swivel jack works great. Plenty strong and smooth cranking motion while raising the trailer tongue. Love it.
by: Garald09/09/2018
Replacement for older tongue jack. Has greater weight capacity, should improve stability on the loaded trailer. Easy to install, all components were included.
by: Ken08/06/2020
Exact replacement for the original which was damaged.
by: MW07/25/2016
Great service. Great jack, the 8'' wheel rolls very well on hard ground.
by: Dave04/17/2020
Heavy duty and the large wheel makes it easy to roll. Used on an 18' Lund Alaskan install was easy. Glad I spent a little extra and went first class. Made in USA, too.
by: Charles 07/07/2022
Replaced original on 16 ft aluminum trailer. Easily mounted and works great.
by: Larry Snarr06/09/2011
Installs easily, folds up easily and quickly. Wheel rolls freely. I have not towed the trailer since installation to see how well it travels yet.
by: Michael03/24/2018
I received the order the next day and was surprised the item #dl22800 was made in the usa , ( real good ). it looks well built with thick metal and nice coating to prevent rust and it jacks up and down flawlessly. I don't know if the wheel is solid or not but it looks like it should last as long as the jack itself.
by: Larry 09/24/2022
Great replacement for rusty old one…very happy! Highly recommend.
by: John 07/14/2020
Great Product! Quick delivery! Easy Installation! MADE IN AMERICA!!
by: Steven 03/15/2021
Very heavy duty, excellent value. A breeze to install. I used the free shipping option and it arrived on time. I am never diappointed when I order from etrailer.
by: johnc06/18/2014
EZ install and works great with 8" wheel
by: J11/30/2022
Works as advertised.
by: Matt 08/24/2021
Very well made and built tough, have had no issues
25
169
Show More Reviews
See what our Experts say about this Dutton-Lainson Trailer Jack
- USA Made Swivel Wheel Trailer Jack for Use in SaltwaterThe Dutton-Lainson Swivel Marine Jacks are manufactured in the USA. These include the # DL22580 and the # DL22800 1500 lb swivel jacks. These are both galvanized steel which will do a great job fighting saltwater corrosion.
view full answer... - Dutton-Lainson Trailer Jack # DL22800 Recommendation for a 3 inch by 5 inch FrameThe Dutton-Lainson Trailer Jack # DL22800 that you referenced will fit trailer frames that are up to 3 inch by 5 inch so it would work very well for you. The capacity for this jack is 1,500 lbs and can has 10 inches of lift. Check out the review video I attached.
view full answer... - Is it Possible to Add a Second Wheel to Dutton Liaison Single-Wheel Trailer Jack # DL22800?If you need a replacement wheel for your Dutton Liaison Single Wheel Jack # DL22800, the part you need is # DL22410. The jack you have is not designed for a second wheel. Instead, I recommend the Fulton Bolt-Thru # FXPD15L. It features a two-wheel design, supports up to 1,500 lbs and can provide up to 12" of lift.
view full answer... - What is the Wheel Made of on Dutton-Lainson Easy Swivel Trailer JackThe wheel on the Dutton-Lainson Pull Pin Easy Swivel Trailer Jack is solid and made a poly molded hard plastic so you won't have to worry about a flat tire. The tire can also be replaced with Replacement Wheel # DL22410
view full answer... - Trailer Jack Recommendation for Trailer with Swivel Dutton Lainson Jack InstalledBased on the picture you submitted the matching trailer jack we have to what you have is the Dutton Lainson part # DL22800. I attached an install video for you to check out as well. At the very worst you may have to use the bolt on brackets that come with this jack, but it looks like this would bolt right up to the bracket you have on your trailer.
view full answer...
- Replacement Wheel Recommendation for Dutton Lainson Jack part # DL22800We do have the replacement wheel you would need for your Dutton Lainson Jack part # DL22800. You would want the part # DL22410.
view full answer... - Trailer Jack Recommendation that Allow Tailgate ClearanceScissor jacks are designed for stabilizing, not lifting. I wouldn't recommend you use one as an A-frame jack. You might be better off with a side mounted jack like the part # DL22800 that can be positioned further back on the trailer frame for more tailgate clearance.
view full answer... - Trailer Jack Compatibility with 14 Inch Tongue SpaceThe Pull Pin, Easy Swivel Trailer Jack with 8" Wheel - Sidewind - 1,500 lbs. by Dutton-Lainson # DL22800 has an overall length of 26-5/8 inches, so it will not fit where you are desiring. The height to the bracket when retracted is 13 inches, but the overall will to too long. The closest I found was the # PS1400300303 which is 11 inches to the center of the bracket when retracted as is # TJBB-2001-B.
view full answer...
- Swivel Jack with Lowest Retracted Height for TrailerThe swivel trailer jack we offer that has the lowest retracted height is the Fulton F2 part # F1413040134 which has a height of 11 inches from the center of its mounting bracket to bottom of wheel. The part # DL22800 has this height a little taller at 13 inches.
view full answer... - Will the etrailer Round, Snap-Ring Swivel Jack # TJBB-2001-B Fit on a 2 inch by 5 inch Trailer FrameWe have several options for a bolt on swivel jack for your trailer with 2 by 5 inch frame (see link). I would recommend the Pull Pin, Easy Swivel Trailer Jack with 8 inch Wheel - Sidewind - 1,500 lbs. by Dutton-Lainson, item # DL22800, for your trailer if the 1500 pound capacity is sufficient for your boat and trailer. These jacks are high quality and designed to fit square tongues up to 3 x 5 inches. The etrailer Round, Snap-Ring Swivel Jack - Bolt On - Topwind - 10 1/2 inch Lift - 2,000...
view full answer... - Trailer Stuck to Truck and Jack Wont CrankUsually, the jaw on the underside of a trailer coupler can be adjusted by tightening or loosening the nut on the underside of the jaw. If you loosen the jaw slightly, you should be able to get the coupler to come off the trailer ball. Once you get the coupler off the ball, lubricate it to make sure the latching mechanism operates smoothly. I like using the spray lithium grease. You'll want to make sure that you're using the correct size trailer ball for the coupler you're using. The coupler...
view full answer... - Should There be a Hole in the Dutton Lainson Jack part # DL22800 The hole you have on your Dutton Lainson Jack part # DL22800 is not designed to be covered. If you really wanted to cover that hole you certainly could although you would be fine leaving it uncovered as well.
view full answer...
- The Retracted Height from the Bottom of the Wheel to the Mounting Bracket on a Dutton Lainson JackI went out into our warehouse and pulled a Dutton Lainson Jack # DL22800 to measure the distance from the bottom of the wheel to the center of the mounting bracket when retracted and found that distance to be 13 inches. Check out the video I attached that shows me taking this measurement. I attached a link to an FAQ article on trailer jacks for you to check out also.
view full answer... - Replacement Jack Handle for 1,000 Pound Dutton Lainson Trailer JackWe do carry replacement handles for Dutton Lainson jacks made after 1996. For the 1,000 pound side wind jacks like # DL22560 you will need replacement handle # DL22446. But it sounds like you may need to replace the gears as well. If a gear stripped out or broke then for replacement gears for the same jack use # DL22437. If the handle or gears broke due to being overloaded then I recommend going with a higher capacity jack. For example jack # DL22800 is rated for 1,500 pounds. I have included...
view full answer... - Swivel Trailer Jack with a Wheel for a 2007 Viking Pop-up CamperThe Fulton jack, # F1411300301, is a weld-on application and you will need mounting bracket # P9012-00. The mounting bracket is the part that gets welded to the trailer frame. Any welding should be done by a qualified professional welder. It can be mounted on the trailer near the coupler (where the tongue weight is lowest) anywhere you have space. A 1500 pound capacity can handle a tongue weight of 1500 pounds. It is very unlikely that any pop-up camper will have a tongue weight that exceeds...
view full answer... - How Do I Know If I Should Replace The Wiring On My Trailer?If the copper wire has turned black, it will mean one of two things. First, salt water somehow got through the insulation/jacket, causing it to severely oxidize. Second, it overheated and actually burned some of that jacket. In either case, I highly recommend replacing you wiring. Compromised wire like this can cause bad connections at best, and/or overheat again and possible catch fire, which would be catastrophically worse. Depending on how you have everything wired and how many accessories...
view full answer... - Pull Pin, Easy Swivel Trailer Jack GreasingThese trailer jacks come pre-greased and must be disassembled to be greased when needed. Dis-assembly starts with removal of the cap at the top of the jack. I have provided a drawing that should help with dis-assembly and re-assembly.
view full answer...
- Trailer Jacks Manufactured in the USAThere are some Dutton-Lainson trailer jacks that are made in the USA as well as a few that are not. Any jacks that we carry that are made in the USA have that as part of the description to help set them apart. Currently we have the following options: Pull Pin, Easy Swivel Trailer Jack with 8" Wheel - Sidewind - 1,500 lbs. # DL22800 Pull Pin, Easy Swivel Trailer Jack with 6" Wheel - Sidewind - 1,000 lbs. # DL22560 A-Frame Trailer Jack - Sidewind - 1,000 lbs. by Dutton-Lainson # DL22530 Pull...
view full answer... - Will the Dutton-Lainson Trailer Jack # DL22800 fit on a 2-1/2 inch Mounting Hole BracketThe Dutton-Lainson Trailer Jack # DL22800 was designed to fit on a 2-1/2 inch diameter mounting hole like what you have so it should work well for you. Check out the install and review video I attached for this jack as well.
view full answer... - What is the Bracket Height on the DL22800 When Fully RetractedThe bracket height on the Dutton Lainson Pull Pin, Easy Swivel Trailer Jack with 8" Wheel # DL22800 is 13", which is the distance from the center of the mounting bracket to the bottom of the wheel on this jack.
view full answer...
- Replacement Trailer Jack with Retracted Height Less than 15 Inches I have 2 trailer jack options that are bolt-on, side frame mount jacks that will offer you lower retracted heights than the 15 inch retracted height of your existing Dutton-Lainson jack. One is a similar Dutton-Lainson jack and the other is a Fulton jack. The Dutton-Lainson Pull Pin, Easy Swivel Trailer Jack with 8 Inch Wheel # DL22800 has a matching bolt pattern to your existing jack but has a retracted height of only 13 inches, measured from the bottom of the wheel to the center of...
view full answer...
- Recommended Trailer Jack That is Made in the USAAny of our parts that are manufactured in the USA have that noted in the item description. If you're looking for an American made product, the Dutton-Lainson Pull Pin, Easy Swivel Trailer Jack with 8" Wheel - Sidewind - 1,500 lbs # DL22800 is a great choice. These are manufactured in Hastings, Nebraska and are one of the best selling brands when it comes to trailer jacks. If that jack won't work for your application, just let me know what size you're looking for and I'm happy to find...
view full answer... - What is the Mounting Hold Spacing for Dutton Lainson 1500 Pound Swivel Trailer JackI went out to the warehouse and pulled Dutton Lainson trailer jack # DL22800 to take the measurements for you. The 3 holes closest together are 1 inch apart on center. From the third hole to the furthest away hole is 2-1/2 inches. Side to side the holes are 5-1/2 inches apart on center. The hole diameters are all 0.39 inches for use with 3/8 inch hardware.
view full answer... - Swivel Jack Option that Can Fit 2 inch Wide Trailer FrameI have a solution for you but all of the swivel jacks we offer are designed to fit 3 inch wide frames. So what you'd have to do with a jack like the part # DL22800 on your 2 inch wide frame would be to use a 1 inch metal spacer to take up the extra space or just run the nuts down further on the mounting hardware since the bolts are threaded from top to bottom.
view full answer...
Do you have a question about this Trailer Jack?
Info for this part was:
Video Edited:
Zack K
Expert Research:
Robert G
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Jameson C
Expert Research:
Adam R
Updated by:
Laura H
Updated by:
Wilson B
Updated by:
Mike S
Installed by:
Cole B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Ken
8/7/2021
Works well