What is the Mounting Hold Spacing for Dutton Lainson 1500 Pound Swivel Trailer Jack

Question

Question:

I have a trailer in need of a tongue jack replacement. The existing jack is bolted to the trailer because of space constraints. Can you tell me what the hole spacing is on the DL22800 and the hole sizes? Thanks

asked by: Mark

0

Expert Reply:

I went out to the warehouse and pulled Dutton Lainson trailer jack # DL22800 to take the measurements for you. The 3 holes closest together are 1 inch apart on center. From the third hole to the furthest away hole is 2-1/2 inches. Side to side the holes are 5-1/2 inches apart on center. The hole diameters are all 0.39 inches for use with 3/8 inch hardware.

expert reply by: Michael H

0

Answer 1

There are some Dutton-Lainson trailer jacks that are made in the USA as well as a few that are not. Any jacks that we carry that are made in the USA have that as part of the description to help set them apart. Currently we have the following options:…

view full answer...

Answer 2

These trailer jacks come pre-greased and must be disassembled to be greased when needed. Dis-assembly starts with removal of the cap at the top of the jack. I have provided a drawing that should help with dis-assembly and re-assembly.

view full answer...

Answer 3

The bracket height on the Dutton Lainson Pull Pin, Easy Swivel Trailer Jack with 8" Wheel #DL22800 is 13", which is the distance from the center of the mounting bracket to the bottom of the wheel on this jack.

view full answer...

Answer 4

Yes, you are correct. As long as your trailer frame is 3 inches wide across that top and 5 inches tall the Easy Swivel Trailer Jack, #DL22800, will fit on your trailer without drilling. I have posted a photo of a jack with the same mount installed on…

view full answer...

Answer 5

I can certainly provide those measurements for you! I spoke with my contact at Dutton-Lainson about the Pull Pin, Easy Swivel Trailer Jack #DL22800 and Replacement Wheel #DL22410. He confirmed that the inner bore of the wheel measures 0.645 inches.…

view full answer...

Answer 6

The hole you have on your Dutton Lainson Jack part #DL22800 is not designed to be covered. If you really wanted to cover that hole you certainly could although you would be fine leaving it uncovered as well.

view full answer...

Answer 7

The swivel trailer jack we offer that has the lowest retracted height is the Fulton F2 part #F1413040134 which has a height of 11 inches from the center of its mounting bracket to bottom of wheel. The part #DL22800 has this height a little taller at…

view full answer...

Answer 8

I went out into our warehouse and pulled a Dutton Lainson Jack #DL22800 to measure the distance from the bottom of the wheel to the center of the mounting bracket when retracted and found that distance to be 13 inches. Check out the video I attached…

view full answer...

Answer 9

We do have the replacement wheel you would need for your Dutton Lainson Jack part #DL22800. You would want the part #DL22410.

view full answer...

Answer 10

If the copper wire has turned black, it will mean one of two things. First, salt water somehow got through the insulation/jacket, causing it to severely oxidize. Second, it overheated and actually burned some of that jacket. In either case, I highly…

view full answer...

Answer 11

The reason why you do not see written instructions for repairs of jacks is the internal parts of a typical trailer jack are not end-user serviceable with the exception of the top gears. And with those it is just a matter of removing the old ones and…

view full answer...

Answer 12

I spoke to a technical contact at Midwest Industries and he advised that they use 800-lb-rated trailer jacks supplied by Dutton-Lainson. I contacted Dutton-Lainson and found the 800-lb jack referred to uses replacement pull pin kit #DL22449. This kit…

view full answer...

What is the Mounting Hold Spacing for Dutton Lainson 1500 Pound Swivel Trailer Jack

Product Page this Question was Asked From

Continue Researching