Summer Starts Here - Save up to 70%
This circuit breaker junction box provides a neat, clean way to mount multiple circuit breakers to the firewall of your vehicle. Junction box has space for seven separate circuit breakers.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to review part number PK52249. This is the Pollak 7-circuit breaker junction box. Now this circuit breaker junction box will provide a nice, neat, clean way to mount multiple circuit breakers to the firewall of your vehicle. The junction box has space for 7 separate studded circuit breakers. Here's an example. I pulled one of the circuit breakers that is designed to fit in here.
It will allow 7 of these to be installed in here. Does provide a nice, neat, clean mounting point for all of the circuit breakers. If you'll notice this metal bar right here is a bus bar and helps dissipate any heat buildup that might occur using the circuit breakers. Basically what you would do is on the circuit breakers they have a little indentation on each end. They're designed to line up with the protrusion on each side of here. What you want to make sure is when you put in a circuit breaker it says aux on one side and battery on the other.
When you install these you want to make sure whatever wiring you have going in is all wired up correctly. Basically the way that you just push them in to the protrusion just like that and it will hold the circuit breaker in place. Then you run your wires in and do all your connections. Now it does include with this junction box the grommets, the holes. There's 2 holes on the side, 2 holes on each end. Whichever 2 you're not going to use, if you're going to run them in the ends and not on the sides, you can just take your solid grommet and just slide it right into place just like that.
Then if you're going to use the ends it includes 4 large-hole grommets that you can just slide in like that on each end. The same way over here. Then that way when you go to put your lid on it pretty much protects any elements from getting inside there and affecting your circuit breakers. Does also come with 4 lid screws so once your lid's going to be attached just like that, put your screws in there, tighten those down. It will hold your lid into place. It also comes with 14 nuts.
What those nuts are for is if you use 7 circuit breakers you'll have 2 nuts for attaching your wires to the circuit breaker. Then the circuit breaker would just pop off. It's held on in those protrusions on the indentations of the circuit breaker. Now I do want to give you a few measurements on this. Put the lid back on. Let's put it over the . There we go, just like that. The measurement I'm going to give you is the length. I'm not going to include the little mounting tabs, so the overall length is going to be 7-1/2" long. The width is going to be 3-3/4 wide. Then the height with the lid on is going to be right at 2-1/2". Then if you take the lid off the height without the lid is going to be right at 1-3/4". Then the measurement if you're needing the measurement of the bolt pattern mounting we'll measure center to center lengthwise and then center to center width-wise. If you put a ruler on it this way lengthwise is going to be right at 8-1/8" and center to center on the mounting holes is going to be right at 3-3/16 center to center for the mounting pattern that way. Going to just pop the grommets back off just like that. I'll put the lid back on and that should do it for the review on part number PK52249, the Pollak 7-circuit breaker junction box. .
Average Customer Rating: 4.9 out of 5 stars (11 Customer Reviews)
This circuit breaker junction box provides a neat, clean way to mount multiple circuit breakers to the firewall of your vehicle. Junction box has space for seven separate circuit breakers.Pretty standard breaker box with good weather resistance. There is enough room to route some cabling but not an enormous amount of room. Worked great to organize and weatherproof my frame mounted breakers.
Product is first class, delivered promp tly.
You guys are great ,helped me adjust my order and everything came fast no worries thanks haven’t had time to install but everything is as it should be
On time
EVERYTHING ARRIVED ON TIME AND WORKED G REAT!!!
Exactly what I ordered. Fast shipping
Thanks you all madecmy day !!!!
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.