To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side tail lights. You will have to remove the trunk floor coverings, rear scuff panel, side trim panels, and tail light assemblies to access this harness. Once you've plugged in the T-connector, run the hot lead up to your car battery. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery.
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your trunk.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. This converter is a circuit-protected, battery-powered unit that bypasses the electrical routes that are used by a basic wiring harness. As a result, there is virtually no draw on your tail light circuits.
Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of the trailer. This converter combines the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
California residents: click here
Average Customer Rating: 4.7 out of 5 stars (108 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.Everything was intact. Looked up the video instructions and they were very clear and easy to follow. Haven't had a chance to do the installation yet. Plan to soon.
Easy installation
Plug and play plugged right into existing wiring harness works great
Came a day early .It will be a while until I get it installed. Have both pieces and excellent rating for quality. Should be a good fit , will let you know when complete.
Product installed easily. Only recommendation is to let users know in instructions that power can be obtained from the rear fuse panel with a spade connection. No need to run wire all the way to the battery for power.
Worked great for a month or 2 then I lost my brake lights and blinkers. All I'm left with are my running lights and sometimes even those don't work. I've looked at my ground and all of my connections and they're all completely fine. And I would go through fuses like crazy. I was changing the fuse almost every time I hooked up to a trailer
This Hitch is great was a breeze to install with some help from a good friend and there are no complaints here fits just a specified with no issues
I have had this for a year On My 2013 Ford Escape
Use it for taking trash to the Dump, as well as got a nice 5X8 Trailer for hauling my tractor and motorcycles and other things.....Not disappointed
It died after 1 year and now all I see is lights on all the time even when the car lights are off.
Jenny N.
6/22/2023
The harness may still be able to be saved. It sounds like that the harness may have a grounding issue or it may have been overloaded. Both are testable and possibly can be fixed. Please see the FAQ below and take a look at method 3 and method 5 for testing the harness.
Helpful Links
Haven't installed yet but seems to be high quality and arrived fast right on time just like always. This isnt my first buy and wont be my last one cause they are good people to work with and help is amazing. Thanks fir all your help and taking care of your customers
Kevin
10/16/2022
The wiring still working great and no problems yet. East to hook up and the instructions was very understandable. Very good product after a year!
I put this in my 2003 Jeep Wrangler along with Break Buddy Stealth. This harness connected in perfectly. The flat tow system is working great one year and ~10k miles latter. etrailer is always best support, pick up the phone and they guide you though buying the right product and installing it.
I like it, I'm glad I bought it. My son and I put it on in about 45 minutes and I put the wiring harness on in about half an hour. I've used it only once so far; it works well. I would buy it again and would recommend it to others.
James G.
7/30/2020
I like it. Its reliable.
It's worked out great with no issues.
Although everything works great and the kit is complete, I was disappointed to see that The connectors for my 2013 escape were outside of the car. I determined the installation would be more waterproof by cutting off the connectors and splicing the traditional way with tap splices behind panels in the trunk.
Otherwise you have to make huge cuts in rubber gaskets to pass the connectors through to behind the tail lights, I didn't want to take a chance of water entering the cabin.
Thus, I would recommend a universal kit for any modern Ford escape.
We backed out of installing this unit after reading the troubleshooting guide. Weren’t comfortable with the possibility of a malfunction in the control box damaging the Escape’s circuitry or driving without functioning tail lights and not knowing it. We’ve installed plenty of hardwired harnesses without this concern.
Took several hours to install, not because of the kit itself necessarily, it snapped in fairly easy. Problems were due to vehicle itself and difficulty accessing areas necessary behind panels and taillights. Installed the power lead wire going through the interior of the vehicle, just didn't feel comfortable with it going down the underside at all. Had to google recommendations for that since it was not covered at all in the directions. Speaking of, directions could be a little clearer, and small dark printed photos don't help as much as they should. Would also recommend you get your own butt connectors with built in shrink wrap for a few dollars more. May just be personal preference, but have never liked those cheap ones that come with kits like this.
As with all custom wiring harnesses from etrailer, this one worked immediately. It was used to replace a similar/older one that had been damaged in a rear-end collision, unfortunately. Everything works as it should, and the Customer Service from etrailer is always the best.
First, I will say the service was great. I had a problem with a wire that came off, and was able to speak to a tech, and he sent me a new one. This probably would not have happened if the product were designed better for my 2014 Ford Escape. You have to put a large object through a very narrow passage under the tail lights. I changed the design by installing my own wires leading from the tail lights down to the bumper area, so all you have to do is fish these wires through, and re-attach. Much simpler and cleaner than the original. Just had to splice a few wires.
Perfect, great instructions
Good product but there isn’t the sufficient length of wiring to complete a normal installation. Had to go to [auto store] and buy additional wire to add the proper length needed.
Sierra K.
7/29/2021
You have to install the wiring harness exactly where the directions say to put the wires or there will not be enough. It shouldnt be loose around moving parts.
I have not installed this yet but I did open the package to review the installation it appears to be very easy to install one thing I did not realize is you have to run a wire from the back of your car to the battery compartment to power up the lights for the trailer which makes sense so you don’t blow the fuse for your cars brake lights if a problem occurs on the trailer
Wiring Harness, the 'Curt' Hitch and Brake Module mounted and Worked Perfectly on my 2014 Ford Escape ,,, Shipping was Fast and Complete. Thank You, Ken H.
I don't usually work on cars. I installed this in my 2016 Ford Escape in my garage with no help except the video and 1 jack stand. It took me 3 1/2 hours. Everything fit like it should, all the parts were there. Fishing the power wire to the battery took most of the time. The guy in the video could stand under the car! I would rate this kit excellent.
Wiring harness worked flawlessly from the getgo. Nearly broke my fingers pushing the plugs through the rubber grommets!
Shipped right away. The instructions were clear and installed without issue.
This wiring harness for my Escape is just what I needed. The factory wiring quit working so I replaced it with the S56335 harness. It cost much less than the Ford replacement parts, and works as well or better than the factory equipment. The installation instructions that came with it made it very easy to install. I definitely recommend this Curt wiring harness.
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jenny N.
12/5/2022
I wanted to see if I could help trouble shoot and I have a few questions that I wanted to ask. When the harness was installed did you run the power wire to the battery? Have you tested the 4 way with a circuit tester to see if the signals are reaching the 4 way? Please see the FAQ that we have below. It is very helpful in helping to identify the issue or determine if a new harness is needed.
Helpful Links
faq-4-5-way-troubleshooting.aspx