Installing a Brake Controller in a 2014 Ford Escape
Question:
I need to know if can splice into the brake switch cold side.
asked by: Eric
Helpful Expert Reply:
To install the Tekonsha Voyager Brake Controller part # 39510 in your 2014 Ford Escape you will need to splice into the cold side of the brake switch with the red wire of the controller. I attached a video that shows a brake controller being installed on a very similar Ford Escape as your 2014 model.
In case you aren't sure what parts you would need you also would need a 4-way to start. For that you would want the # C56335. Now to convert that to a 7-way and install the brake controller you will need the part # ETBC7. I attached install instructions for these products for you to check out also.
Products Referenced in This Question
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
Tekonsha Voyager Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Manual Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- Indicator Lights
- Up to 90 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Shop: Trailer Wiring
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Lippert Components Single Flexguard RV Slide-Out Kit Hardware
- Q&A: Flange to Flange Measurement on RV Slide Out For Slide Topper Awning Fit
- Shop: Replacement Heating Element for 6-Gallon Hott Rod Water Heater Conversion Kit
- Shop: LaSalle Bristol Toilet Floor Flange for RV - ABS Plastic - 3" Hub x 4" Diameter
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Hitch
- Video: Choosing the Right Trailer Wiring
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Search Results: 44649
- Shop: Fifth Wheel Hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: 68149
- Shop: Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Video: Choosing the Right Brake Controller
- Article: Trailer Wiring Diagrams
- Shop: Gooseneck Hitch
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: 25580
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End
- Video: Lippert Solera Slider Slide-Topper Review
- Search Results: dust cap
- Article: Brake Controller Installation: Starting from Scratch
- Q&A: Replacement Trailer Grease Seals for Allis 5013 29772
- Q&A: 2022 Toyota Highlander Wiring for a 7-Way Blade Connector
- Search Results: dust caps