CE Smith Bolster and Swivel Bracket Assemblies - Galvanized Steel - 13" - Qty 4
(73 reviews)
Price: $55.44
In Stock
CE Smith Bolster and Swivel Bracket Assemblies - Galvanized Steel - 13" - Qty 4
Item # CE10002G-4
Our Price: $55.44
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (73)
- Q & A (0)
- Photos
CE Smith Boat Trailer Parts - CE10002G-4
- Bunks
- Bunk Bracket
- Swivel Bracket
- 3-1/2 Inch Long
- Galvanized Steel
- 12 Inch Tall
- 2 Inch Tall
- 1-3/8 Inch Wide
- 2-1/2 Inch Wide
- CE Smith
Rust-resistant assemblies let you install 2 bunk boards on your boat trailer. Swivel brackets enable bunks to tilt when loading a boat. Mounting slots allow for height adjustment. Dimpled surfaces keep brackets from sliding along the trailer frame.
Features:
- Bolster-and-swivel bracket assemblies allow you to install 2 bunk boards on your boat trailer
- Dimpled bolster bracket surfaces help prevent the brackets from sliding along the trailer frame
- Mounting slots permit as much as 3-3/4" of height adjustment during installation
- Each bolster bracket installs on your boat trailer's frame with a U-bolt (sold separately)
- Strong swivel brackets let you tilt the bunk boards
- Helps you to fit the boat hull snugly onto trailer during the loading process
- Hardware is included for attaching the swivel brackets to the bolster brackets
- 11-Gauge, galvanized steel resists rust and corrosion
- Suitable for saltwater exposure
- Made in the USA
Specs:
- Quantity: 4 bracket assemblies
- Overall height: 13"
- Dimensions of bolster bracket: 12" tall x 2-1/2" wide
- Mounting slot dimensions: 4-3/4" long x 1/2" wide
- Spacing between mounting slots: 1/2"
- Dimensions of swivel bracket: 3-1/2" long x 1-3/8" wide x 2" tall
- Flange mounting hole diameters: 3/8"
- Flange mounting hole spacing: 2-1/2" apart on center
Bolster-and-swivel-bracket assemblies are typically mounted upright on a boat trailer's crossmembers. They allow a mounted bunk board, which runs from the front of the trailer to the back, to tilt to accommodate and support boat hulls of different sizes. On kayak trailers, these brackets are mounted to the trailer's frame and support bunk boards that run across the trailer.
Galvanized Steel
Steel parts are galvanized by being hot-dipped in zinc after they have been stamped. This creates a coating that is typically 3 mil to 5 mil thick. This thick, all-around coating allows galvanized steel products to provide years of use without rusting or corroding.
10002G C. E. Smith 11-Gauge Galvanized Steel Replacement Bolster and Swivel Brackets - 13" Tall - Qty 4
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- Alternate product found
Customer Reviews
CE Smith Bolster and Swivel Bracket Assemblies - Galvanized Steel - 13" - Qty 4 - CE10002G-4
Average Customer Rating: 4.6 out of 5 stars (73 Customer Reviews)
Rust-resistant assemblies let you install 2 bunk boards on your boat trailer. Swivel brackets enable bunks to tilt when loading a boat. Mounting slots allow for height adjustment. Dimpled surfaces keep brackets from sliding along the trailer frame.by: John ‘56 Resorter05/08/2024
Very easy to install. Fully adjustable up/down and tilt side to side by several degrees. Great product with high grade hardware. It took only 45 minutes to install this outboard pair of bunks. I will buy from etrailer again!!
by: Doug10/02/2022
Worked great in converting a pontoon lift to a boat lift for my sons 18 ft fishing boat
by: Jeff 05/09/2024
I used these to build a jet ski lift and it is working great. I used the long 13" set so I could make one ski higher than the other to make it easer to keep one in place when using the other.
by: James 12/23/2022
Very excited about the Service and quality of my items. Love the delivery time being as promised.
The you and Happy Holidays
by: Timothy05/11/2024
I am hoping it will work on my trailer. All the parts are as you described. The ordering was easy and shipping was fast. Thank you
by: JEff N04/02/2014
Converted a late 80's EZ-Loader roller to a bunk construction for my Boston Whaler 18 Outrage. Great product and easy to use. Quality construction and perfect fit. Purchase the recommended extra washers for the U bolts, worth it.
by: Gary 09/09/2023
Super service, fast shipping, excellent product. Will definitely be my go to place for quality trailer parts.
by: James08/03/2017
Saviors are the folks at etailer.com. Converting rollers to bunks was simple. Rook off all the rollers, measured up the trailer and boat, went to etrailer to shop for ALL the parts to make the conversion. Placed order, for all my needs, got over the $99 shipping hurdle and three days later, got to working on the actual conversion. Within a few hours, my EZ-Loader that my Whaler sits on, was now on brand new bunks, resting comfortably.
by: Mike 07/05/2023
Perfect for what I needed already installed. Very quick delivery
Great service Thanks Mike
by: Philip 08/14/2023
Exactly what I needed
by: Jonathan07/05/2018
The trailer brackets have performed well for over one year. They are quite durable and the galvanized coating ensures that they don’t rust even in salt water. They fit right in on my EZ Loader trailer.
by: S. Harper09/10/2014
I ordered these boat trailer bunk brackets to modify a trailer I bought to fit the boat I have. The brackets were just right for what I needed and of good quality and durable. I received them in a timely matter, about 4 days with the regular shipping method. I will definitely order from Etrailer again for my trailer needs.
by: Ricky06/30/2019
So far, the product has been excellent. Haven't had a chance to use the unit in the water yet, but am working on building my boat for the trailer. It was nice to hace a service person help me find what I was looking for on your web site. Give me another month, and I can send pics of the newly installed parts. Thanks.
by: John 07/30/2023
Great products as fast delivery!!!
by: Captain Nancy09/14/2016
These brackets replaced the old rusty bunk brackets on my salt water trailer.
Measure the height of the bunks on your trailer now and order ones that will be tall enough. They are adjustable by the slots you can see in the bracket. VERY EASY to install with the U bolts. The tops swivel easily so you can tilt the bunks the way they need to be to fit your boat properly.I have never worked on a trailer before, this was a first and it was easy. Check out the videos and photos provided. OUTSTANDING COMPANY with outstanding products.
by: Ilya06/17/2020
Really flimsy brackets. One broke off, causing bunks to fail, breaking other brackets and causing $$$$ in damage to my boat hull. Its not a heavy boat either (about 2,500 lbs, 19ft boat). Do not buy these if you like your boat and don't want to repair your hull. Maybe these can work for a jet ski or something, not a boat.
by: Scott12/08/2018
Haven't actually tried the bunks and guide boards I bought because it is winter here now but the service and selection were awesome. They had everything I was looking for in one place and the delivery was right on time. The instruction videos and pictures were very helpful. Highly recommend etrailer for all your trailering needs and more.
by: Timothy 06/29/2022
Heavy duty used to convert a roller trailer to bunks. Shipped promptly. Would buy from this merchant again and again.
by: Robert04/11/2018
I so wish I had discovered etrailer earlier! The same product was $30 more expensive at other places and shipping was very prompt! Additionally, Heidi M. was an absolute joy to work with! She was friendly and truly interested in helping me find what I needed. She is definitely my go-to person whenever I need trailer parts from now on! Thanks, Heidi!! :)
by: Migs10/04/2017
So far so good. Brackets have held up well this past year and hope they last a long time.
by: john c06/30/2016
the 12" risers i purchase were put on yesterday, I liked the height for ajusting, very strong does not move at all, great product.
by: David 07/12/2021
These are solid swivel bracket assemblies however I'm still struggling as to how I am going to install them and if I need additional parts. I give the site a below average score however the products are well made.
by: Marv 12/07/2021
Well built product. I’ll take some photos when I get these brackets installed!
by: Shane G.10/10/2016
Excellent product, exactly what I was looking for. Thank you for sending it so quickly. Will definitely do more business with etrailer.com
by: Dwight D.10/18/2014
They are great, well made and easy to work with and the hardware is of quality and heavy gauged. Good job. Dwight
25
73
Show More Reviews
See what our Experts say about this CE Smith Boat Trailer Parts
- Can Top of CE Smith Swivel Bracket be Tightened to Keep Them at AngleThe top of the swivel bracket is not something that can be tightened to completely stop the swivel for the CE Smith Bolster and Swivel Bracket Assemblies # CE10002G-4. So there is always going to be some swivel in these brackets to ensure that they are always at the correct angle when being loaded. I also wanted to mention that to install these brackets you will need U-bolts, the CE Smith U-Bolts # CE15283GA-4. I have added some links below to video reviews for you to check out as well...
view full answer... - Bunk Boards or Roller Bunks and Brackets for Boat Trailer and 26 Cuddy Cabin BoatI don't believe there is a style of trailer called a low-tide trailer. Most of what you find on an internet search of that term is a broken boat trailer, so the gentleman may have been telling him his trailer was broken or soon to be broken. I've never seen bunk boards resting directly on the frame, so I recommend getting some bunk brackets. I recommend the CE Smith Bolster and Swivel Bracket Assemblies - Galvanized Steel - 13" - Qty 4 # CE10002G-4 along with the CE Smith U-Bolts -...
view full answer... - Are There 7 Foot 2x4 Bunk Boards For Jet Ski TrailerWe do have bunk boards that are 7 foot long 2x4's for your jet ski trailer, which are the following part number: - CE Smith Carpeted Bunk Boards for Boat Trailers - 7' Long # CE27845 To mount them you can use bolster brackets, and choose the height that is correct for you, the CE Smith Bolster and Swivel Bracket Assemblies - Galvanized Steel - 9" # CE10000G-4, 11" # CE10001G-4, or 13" # CE10002G-4 with CE Smith U-Bolts - Galvanized - 3-13/16" Long x 3-1/16" Wide # CE15283GA-4.
view full answer... - How Many Bolster And Swivel Brackets Are Needed For A Boat TrailerI spoke with my contact at CE Smith, and they said the Bolster and Swivel Bracket Assembly for Boat Trailers, like part # CE10000G, do not bear the weight of the boat. The U-bolt that attaches the brackets to the trailer frame support the weight of the boat. There should be a bracket attached to each cross member of the trailer frame. If you are buying several brackets, I would recommend part # CE10000G-4. This is a set of 4 of the 9 inch adjustable brackets. If you need longer adjustable...
view full answer... - Determining Trailer Bunk Board Length for 14 Foot Sailboat It's not an exact science but typically you want the bunk boards on a trailer to extend all the way to the rear of the boat. It wouldn't hurt to have them go a bit beyond this too to ensure proper support during travel. Since the front of the boat should be supported by the bow stop you usually see bunk boards that measure about half the length of the boat itself. Since you no longer have the boards that originally came on your trailer it might also be a good idea to try and contact the...
view full answer... - Bolster Brackets and Swivel Assemblies for SeaDoo TrailerI can help you find the correct bolster and swivel brackets for your Seadoo trailer. The CE Smith part # CE10002G is a galvanized 13 inch bolster with a swivel bracket assembly. The swivel bracket will fit your 2 x 4 bunk great, but the brackets included have a 2-1/2 inch center spacing. We do offer a swivel bracket with a 2 inch center spacing # CE10206AA, but with either I would recommend drilling a hole in the bracket where you need it. It's important to keep in mind that its a...
view full answer... - How High Will CE Smith 13 Inch Bolster Bracket Sit Above 3 Inch CrossmemberThe # CE10002G-4 CE Smith Bolster and Swivel is 13" tall. Assuming you mount it at the position to gain the most height, you should have 9" remaining. Losing the height from attaching to the 3" crossmember leaves you with 10" remaining. You will lose 1" at the bottom with the 1/2" below the lower mounting hole and 1/2" diameter U-bolt. Accounting for the added height of the bunks, you should be sitting over 11" once installed. I have attached a video review of the bracket for your reference.
view full answer... - Parts Needed to Add Bunk Boards to Boat TrailerTo add bunk boards you'll simply need the bunk boards and mounting brackets which attach to the front and rear crossmember of your trailer frame. If you already have brackets you may be able to use them, otherwise, you just need the correct length of boards and brackets: - CE Smith Carpeted Bunk Boards for Boat Trailers - 4' Long # CE27810, 5' Long # CE27820, 6' Long # CE27840, or 7' Long # CE27845 - CE Smith Bolster and Swivel Bracket Assemblies - Galvanized Steel - 9" # CE10000G-4,...
view full answer... - Bunk Brackets and Keel Rollers for Magic Tilt Boat TrailerWe do have bunk brackets and keel rollers that you can use with your Magic Tilt boat trailer, though not that size leaf spring. For the brackets you only need to choose the size you want: - 9 Inches: CE Smith Bolster and Swivel Bracket Assemblies # CE10000G-4 - 11 Inches: CE Smith Bolster and Swivel Bracket Assemblies # CE10001G-4 - 13 Inches: CE Smith Bolster and Swivel Bracket Assemblies # CE10002G-4 With each of these brackets you can attach them with CE Smith U-Bolts # CE15283GA-4. As...
view full answer... - What Replacement Swivel Heads do You Carry for My Boat Roller Bunks on My Trailer?If you have a boat bunk bed bracket system that has swivel heads like the CE Smith Bolster and Swivel Bracket Assemblies - Galvanized Steel - 9" - Qty 4 # CE10000G-4, the only way to extend the length of them is by purchasing longer swivel heads. Currently, our longest swivel heads we carry are 3-1/2 inches long. Those are the Swivel Bracket for Boat Trailers - Zinc Plated Steel - 3-1/2" Long # HP35FR. Unfortunately, if you need anything longer than that, you would have to do a custom fabrication...
view full answer... - Recommended Bunk Board BracketsWe definitely have options for brackets to mount your bunk boards. This will depend on the size needed, of course, but here are a couple options for you to take a look at. The CE Smith # CE10003G-4 will come as a 4 pack and are 11 inches tall, including the swivel bracket on the top. If you need a little more height, the # CE10002G-4 will be much the same, but measure 13 inches. The swivel bracket on the top pf these will let you angle your bunk boards to the angle that suits your needs best.
view full answer... - Determining Length of Bolster Bracket for New Bunk System on Boat Trailer To be on the safe size, I recommend going with a 13 inch bracket # CE10002G-4 at the back of the trailer and an 11 inch bracket with # CE10003G at the front. A nice feature on these brackets is that they will each actually have as much as 3-3/4 inches of height adjustment due to their mounting slots, so even if its total height is a bit higher than needed, you can adjust them down. This will allow you to have the perfect height for your new bunk support system. I have attached a short...
view full answer... - Weight Capacity And Parts Needed For Modifying Boat Trailer For 26 Ft Regal CommodoreI spoke with my contact at CE Smith, and they said the Bolster and Swivel Bracket Assembly for Boat Trailers, part # CE10000G, do not bear the weight of the boat. The U-bolt that attaches the brackets to the trailer frame support the weight of the boat. There should be a bracket attached to each cross member of the trailer frame. If you are buying several brackets, I would recommend part # CE10000G-4. This is a set of 4 of the 9 inch adjustable brackets. If you need longer adjustable brackets...
view full answer... - Dimensions of the CE Smith Carpeted Bunk Boards # CE27810 and Availability of Swivel BracketsThe CE Smith Carpeted Bunk Boards # CE27810 that you referenced do measure 48" long x 1-3/4" wide x 3-3/4" tall. There are swivel brackets available for adjustable height. For an overall height of 9" you will want part # CE10000G-4, for an overall height of 11" part # CE10001G-4, and for 13" part # CE10002G-4. I have attached a review video of the bunk boards being installed for you to check out.
view full answer... - Parts to Convert Roller Bunks to Bunk Boards on Boat TrailerIt sounds like you are just wanting to switch to carpeted bunk boards. For that you can use the CE Smith Carpeted Bunk Boards for Boat Trailers, which come in a number of different lengths: 5 feet long # CE27820, 6 feet long # CE27840 or 7 feet long # CE27845. To install these you can mount them to brackets that are already on your trailer or use CE Smith Bolster and Swivel Bracket Assemblies; you would need two of these per bunk board. The assemblies are available in different lengths...
view full answer... - Do CE Smith Bolster and Swivel Bracket Assemblies Have a Weight CapacityThe CE Smith Bolster and Swivel Bracket Assemblies # CE10002G-4 don't have a weight rating, as they will be able to handle whatever the bunks installed on them can handle. We've confirmed this with CE Smith in the past.
view full answer... - Recommended Replacement Brackets And Hardware For Karavan SLT-5000For your boat trailer, I recommend the CE Smith Bolster and Swivel Bracket Assemblies # CE10002G-4. These brackets are available in different heights. These brackets are held to your trailer with u-bolts like the CE Smith U-Bolts - Galvanized - 3-13/16" Long x 3-1/16" Wide x 1/2" Diameter # CE15283GA-4. These brackets hold on your Bunk boards like the CE Smith Carpeted Bunk Boards for Boat Trailers - 6' Long - 1 Pair # CE27840 that are available in different lengths or the roller bunks...
view full answer... - Can Boat Swivel Bunks Be Tightened So they Won't MoveThe nuts that hold the swivel to the brackets like on the # CE10002G-4 can be torqued down to prevent movement if desired.
view full answer... - Does the CE Smith Swivel Bracket Come with a Bolster BracketThe swivel bracket # CE10200G is just the L-shaped bracket. it can attach to a bolster bracket. To get the bolster bracket with the swivel already on it you can use one of the following: # CE10000G, 9 inches tall # CE10001G, 11 inches tall # CE10002G, 13 inches tall There are also sets of 4: # CE10000G-4 # CE10001G-4 # CE10002G-4 I have also included a link to the bolster brackets we carry with and without swivel brackets attached.
view full answer... - Switching From Roller Bunks to Carpeted Bunk Boards for 20 Foot TrailerYou can switch from roller bunks to carpeted bunk boards, and for a 20 foot trailer you will simply need to add four of the 5 foot CE Smith Carpeted Bunk Boards for Boat Trailers # CE27820. You can attach them to your trailer frame with the appropriate length of swivel brackets, depending on what you need: - 9 Inch: CE Smith Bolster and Swivel Bracket Assemblies # CE10000G-4 - 11 Inch: CE Smith Bolster and Swivel Bracket Assemblies # CE10001G-4 - 13 Inch: CE Smith Bolster and Swivel Bracket...
view full answer... - What is the Difference Between a Bolster Bracket and a Bunk BracketThe terms bolster bracket and bunk bracket refer to the same thing. For example, CE Smith part # CE10002G-4 is a bracket that can be used on a boat trailer to mount either a standard carpeted wooden bunk board (that supports the boat's hull) or a roller bunk like # DL21741.
view full answer... - Parts Needed To Replace Rollers With Bunk Boards on a ShoreLand'r R22L Boat TrailerFirst you will need to remove your roller assemblies and install CE Smith Bolster and Swivel Bracket Assemblies # CE10002G-4. You will need the CE Smith U-Bolts # CE15283GA-4 to secure them to your 2"x3" crossbars. You will need to source treated lumber for your bunk boards locally and cover them CE Smith Deluxe Marine-Grade Carpeting # CE11330.
view full answer... - Replacement Bolster and Swivel Brackets Over 9 Inches TallTo gain more height you will want to trade out your brackets with taller ones. We have the following options: CE Smith Double U-Bolt Bolster and Swivel Bracket Assemblies - 10-1/4" - Qty 4 # CE10191GA-4 CE Smith Bolster and Swivel Bracket Assemblies - 11" - Qty 4 # CE10001G-4 CE Smith Double U-Bolt Bolster and Swivel Bracket Assemblies - 12-1/4" - Qty 4 # CE10192GA-4 CE Smith Bolster and Swivel Bracket Assemblies - 13" - Qty 4 # CE10002G-4 CE Smith Double U-Bolt Bolster and Swivel Bracket...
view full answer... - Can 6 of the CE Smith Bolster Brackets CE10002G-4 be OrderedYou would just need to order a quantity of 6 of the part # CE10002G to get six of the brackets that come with the part # CE10002G-4.
view full answer...
Do you have a question about this Boat Trailer Part?
Info for this part was:
Edited by:
Frances L
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Adam R
Video Edited:
Jeff D
Written by:
David L
Updated by:
Chelsea B
Updated by:
Wilson B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
James
12/23/2023
Im totally happy with my purchase,and the service I received was professional and excellent!