Customers prefer these similar products
Features:
Specs:
Replaces # C31004
Average Customer Rating: 4.8 out of 5 stars (44 Customer Reviews)
this was the project at hand . I built the winch carrier and needed your front receiver hitch to attach to the 1998 Chev and give it more solidity to handle any thing that came up . Awesome product great doing business with y'all. From Morehead City North Carolina . THANKS
Five, Front Receiver hitch and Winch Mount. Pictures say a thousand words. Would Recommend.
This item has been great, I flat tow a 1997 Jeep Cherokee behind my motorhome. After I remove the tow bar, this item allows me to install my winch on the front of the Jeep for some off road fun.
Wife didn't want a beefy new bumper on the grocery-getter all year around. So, I tried this front receiver route for my infrequent off-road needs. First, it came quickly and was well packaged. E-trailer was great to deal with.
Receiver is quite strong itself, but it is fastened with 6 bolts, none of which actually goes into the Jeep frame (only into about 1/16 steel). 2 bolts each side go through one side of the vertical upright piece that hangs the cross-tray from the frame behind the stock bumper. The other 2 go trough the big holes in the bottom of the thin steel bumper liner. If your winch does ever over-pull, it is far more likely to damage the Jeep than the receiver, I suspect. I have not been able to get a good definition of what “line pull” means but I have been told it's a rolling load type measurement being way lower in terms of static pull equivalent.
Mounted, the receiver backs up to the cross-tray. The issue with this is that when used with a plate like the Curt 31010, it won't allow the plate to be fully inserted such that you can access the 3rd (deepest) hole. This leaves the mounted plate sticking out about 3” from the front bumper face and certainly adds unwanted leverage to any off center pull condition. It also looks bad. I've debated cutting off the 2” bar about an inch (or alternatively cutting a notch in the top of the jeep crosspiece). Both fixes have drawbacks. I don't like cutting the jeep, but if I shorten the plate shaft by a hole, I might have issues using it in the back receiver without having to remove the spare tire (or carrying a receiver extender). In place, the plate is quite wobbly in the receiver and creates a noise concern if driving bumpy roads . I may weld some shims to tighten the fit. Suggestion: Before you bolt the receiver on, put your plate in it with the pin in the deepest hole. Then take a pencil and mark the plate shaft where/if it sticks out the back of the receiver. You will then know exactly how much would need to be trimmed if you decide to later.
Bottom line, I'm thinking about something more akin to a UTV winch (3-4.5k) for the receiver mount. I can still will carry a snatch block as a doubler in rare cases I need more.
Regarding installation, I had the whole bumper off. While this is not necessary, I think it would be absolutely crazy not to at least remove the horizontal plastic piece on top of the frame just behind the bumper so you can see everything you are doing from the top. Two plastic push pins with Phillips screws release it.
Think long and hard at a beefy front aftermarket bumper if you think you may need some really heavy duty winching.
I installed the front hitch bar to expand the flexibility and uses for my truck. The hitch fit nicely with only minor adjustments. I was easily able to install the hitch by myself. I have two primary plans for the hitch: 1- Use a trailer ball to move two trailers I have around my work area with precision and less guessing by facing forward. 2- I have a front winch plate that can be added as needed to use a winch for those off road needs.
The staff at Etrailer were most helpful especially arranging a special delivery time to be sure I was home when it arrived.
Works as it should and I have definitely pushed the limits of my winch, receiver and this plate with no issues. (7k truck + 11k trailer, up a fairly steep hill; my poor winch).
The Badlands 12,000 lb winch bolt pattern fits the holes to be used for the handle set, so don't plan on using the handles with the Badlands 12,000 lb winch without buying new longer bolts. Lots easier than making one from scratch, which is what I've done before. Guess @ 70 I'm getting lazy.
received product, was as described, no real instruction needed as it fit perfectly into receiving hitch, it did include a recommended towing/winching angle instruction page
My Warn winch fits perfectly on this mounting plate, truly allows me multiple winching possibilities from the front or back of the truck.
Product as described. Holds/supports my winch great!
Just what I wanted for a project I that was working on. Found one local that was a little cheaper, but they had no stock. Now I can use my winch on the back of my truck or mount it to my trailer.
Just got my winch plate.... I love it. I got my truck all set up for spring and summer. Once again etrailer To The Rescue.... Thank You guys.
The front receiver for my 2019 Jeep JL arrived on time and fit like socks on a rooster. Installing took about 30 minutes. A tip leave air dam off.
All three items that I ordered arrived sooner than anticipated and in perfect condition. Very seldom does an on-line purchase exceed my expectations like this order with etrailer.com! Thanks!
Great Product! Exactly what was described from the item description.
Very fast delivery. Cant understand why this product came quicker to a LA address when an order was placed from another website within 60 miles and will not receive until 3 days from now.
Will stop at this site first next time.
Price was right and product worked perfectly!! I asked for UPS ground shipping ( 7 -10 days ) and it arrived in 4 days, I would definitely order from etrailer again!!!!
Beefy and bought with confidence from e trailer
The products I ordered did exactly what you said they would do.
Quick delivery and even a year later follow up.
Can't get better than that.
Used to mount a removable winch on my 2004 Grand Cherokee. Works great and very well made.
the product is sturdy and well built and still mounted,thanks henry
Very well made, good looking welds, no porosity visible. Nice heavy metal throughout, should hold up very well. Can’t wait to mount the winch and go find a nice sturdy tree to pull against.
Great product. Very heavy duty! Can’t go wrong with it. Excellent customer service and shipping!!!
Excellent customer service.
This product is high quality and made from thicker steel than the units found on other online retailers.
I bought this for my husband to go with his winch set up and he loves it... I will be ordering more stud from you guys...
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.