Does Curt Front Mount Trailer Hitch Receiver # 31241 Require Cutting the Bumper on 2014 Frontier

Question

Question:

Do you have to cut the front bumper to mount

asked by: G G

0

Expert Reply:

The front-mount trailer hitch receiver you referenced, Curt # 31241, is a fit for specific Nissan and Suzuki vehicles including your 2014 Frontier.

No drilling is required but the air dam (lower fascia) and tow hooks must be permanently removed for hitch installation. No cutting is needed either. You will need a torque wrench to secure the fasteners to the specified rating as indicated in the written instructions from Curt which are linked for you at right.

expert reply by: Adam R

0

Answer 1

When using a single set of tire chains on a vehicle that is 4 wheel drive or all wheel drive you want to install the chains on the primary drive axle. Typically this will be listed in the owner's manual. But for a 4WD drive vehicle the axle…

view full answer...

Answer 2

The anti-rattle adapter I recommend is the No-Rattle Trailer Hitch Wedge, part #MPG908. This will work for 1-1/4 inch and 2 inch receivers and is designed to insert into the small gap that may exist on your receiver. You then tighten it up after it…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

The Dexstar Conventional Steel Wheel with Offset #AM20504 is an excellent replacement option for your application as it fits the Goodyear Endurance ST205/75R15 Radial Tire and your baby moon hubcaps perfectly! Just be sure to check and make sure…

view full answer...

Answer 6

The Draw-Tite Front Mount Trailer Hitch Receiver part #65075 is a fit for a 2010 Nissan Frontier and will require either removal or modifications to the center air dam trim piece or skid plate if present. I have attached a photo for you that shows…

view full answer...

Answer 7

The only type of hub/wheel cap we have that will fit a 14" wheel is the Americana Baby Moon Trailer Wheel Center Cap part #AM90086. This wheel cap simply snaps onto a conventional 5 lug wheel and provides a stylish chrome plated steel cap that…

view full answer...

Answer 8

The Draw-Tite front-mount hitch #65075 is a confirmed fit on your 2017 Nissan Frontier. From the tops of the frame brackets that contact the frame down to the bottom of the receiver tube the dimension is 6-inches according to my Draw-Tite contact.…

view full answer...

Answer 9

Yes, you will need to remove the center air dam on your 2015 Nissan Frontier to install front mount hitch #65075. Nothing should have to be modified though and if you even take the hitch off you could put the air dam back into place.

view full answer...

Answer 10

In regards to the Draw-Tite Front Mount Trailer Hitch Receiver part #65075 which is a fit for a 2016 Nissan Frontier, the distance from the ground to the bottom of the receiver tube opening is around 9-1/2" but this can vary for each application…

view full answer...

Answer 11

Yes, you can absolutely use your Yakima Rocketbox #Y07192 with a Thule Wingbar setup. The Rocketbox is made to fit virtually any crossbar shape. You were spot on with the other parts you picked out for your 2021 Kia Niro EV. It will be #TH711220 for…

view full answer...

Does Curt Front Mount Trailer Hitch Receiver # 31241 Require Cutting the Bumper on 2014 Frontier

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching