Front Suspension Enhancement Recommendation for a 2015 Chevy Silverado 3500

Question

Question:

It says that 4 bumpers are included. Is this the correct number included? Most other kits only include 2. I just need to know how many kits to order, 1 or 2 for my chevrolet.

asked by: Jason R

0

Expert Reply:

The SuperSprings Vehicle Suspension # SSF-202-47 that you referenced comes with enough bump stop replacements to do the front end of your 2015 Chevy Silverado 3500. Since there are two per side on your vehicle a total of 4 comes with this kit.

I attached a set of installation instructions to the right for you to check out as well.

expert reply by: Jameson C

0

Answer 1

Yes, you can use both the SuperSprings Custom Suspension Stabilizer #SSA13MXKT with a set of SumoSprings #SSR-203-47-2. These will not increase the weight capacity of your vehicle, they will improve your ride quality and reduce squat when hauling…

view full answer...

Answer 2

For your 2015 Chevy Silverado 2500HD towing a 12,000 lb fifth wheel trailer I recommend the SumoSprings Solo Custom Helper Springs #SSR-207-47, because Timbrens will make your ride a bit rougher than the SumoSprings. The SumoSprings work by…

view full answer...

Answer 3

Yes, you should definitely upgrade the front suspension on your 2020 Chevy Silverado 2500 if you're going to be using the EcoHitch Hidden Front Mount Trailer Hitch Receiver item #EH57FR. That much weight will put a lot of stress on your factory…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 8

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...