What is the Diameter of the Cable on Hopkins 7-Way Molded Trailer Wire Connector # HM20048

Question

Question:

Do you know the diameter of this cable?

asked by: John O

0

Expert Reply:

On the Hopkins 7-Way Molded Trailer Wire Connector # HM20048 the outer diameter of the cable is 5/8 inches.

On the inside the red, green, yellow and brown wires are 14 gauge, the blue wire is 12 gauge and the white and black wires are 10 gauge.

expert reply by: Michael H

0

Answer 1

The Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 23" Lift - Item #JET-5000 that you referenced only has one wire that runs from it, the power wire. This wire would need to get run to the 12 volt accessory circuit of the 7-way…

view full answer...

Answer 2

I would first recommend checking to see if the breakaway pin is still intact. If the pin has not been pulled, you will want to begin by checking the trailer connectors for dirt or corrosion on both the inside and outside. Once the breakaway pin and…

view full answer...

Answer 3

Pretty much the only difference between the Engager breakaway systems #20099 and #20400 are the designs of the battery boxes. Both function the same and have the same features. Engager #20400 is meant to be mounted to the side of the trailer frame…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 9

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 10

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 11

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 12

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

What is the Diameter of the Cable on Hopkins 7-Way Molded Trailer Wire Connector # HM20048

Product Page this Question was Asked From

Continue Researching