Replacement Gears for Fulton and Bulldog Trailer Jacks

Question

Question:

I would like to buy some bearing kits for fulton magnum 09 260 19 and bulldog 3000lb # 151101 stands , please advise costs.

asked by: Marc L

0

Expert Reply:

Parts are no longer available for the old Fulton Magnum jacks unless it is one of the following jack models: TJ503/C, TJU503, PMJ53, TJ507/C, PMJ75, CS750, GR700/TJ712, XP10/6/W/WC and XP100. Then you would use # F0933302S00.

But we do have parts for Bulldog trailer jack # BD151101. We have handle and gear kit # BD500256 that you could use.

expert reply by: Michael H

0

Answer 1

What we have heard is that the Fulton #FTJ120W0301 does fit the mounting plate of the Shelby Jack 5784.

view full answer...

Answer 2

The jack I recommend to replace your Fulton 1000 lb jack with bolt through is the Fulton Bolt-Thru Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,500 lbs #FXP15W. This is a very sturdy jack that will give you a little added safety as you…

view full answer...

Answer 3

I spoke with my contact at Bulldog and found that you will need to use kit #BD500256 for the 2K Bulldog jack #BD1500520317. This jack used 3 different gear sets over the years so this kit when used with the included handle and other parts spans all…

view full answer...

Answer 4

Yes, we do have kits to rebuild jacks, I am not certain what model you have but if it is the 2,000 lb. Bulldog Jack we have the replacement sidewind handle and gear kit listed under, #BD500256. This will fit the following jack models: Bulldog round,…

view full answer...

Answer 5

Shelby has been out of business for a number of years now and so there unfortunately are no replacement parts readily available. You might be able to find something where old parts are regularly sold, but you'll probably have to do a lot of…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Replacement Gears for Fulton and Bulldog Trailer Jacks

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching