Replacement Sidewind Handle and Gear Kit for Bulldog Round Jacks

Question

Question:

The gear slips on the crank handle under load. Free load works fine. can this be repaired? On you website shows a replaceable gear box and says it is for 2in id and 2 1/4 or 2 1/2 od. mine is 1.625 od, what are my options?

asked by: Jack H

0

Expert Reply:

Yes, we do have kits to rebuild jacks, I am not certain what model you have but if it is the 2,000 lb. Bulldog Jack we have the replacement sidewind handle and gear kit listed under, # BD500256. This will fit the following jack models: Bulldog round, sidewind jacks with 2,000-lb capacity: BD151401, BD151421, BD151460, BD151464, BD151101, BD151110, BD155022, BD155028, BD155033, 155100, BD155157, BD151443, BD154102, BD154107, BD150037, BD150152, BD1500520317, and BD150000. Please see the attached video to assist in rebuilding.

If you have a Fulton F2, we longer have gear kits.

expert reply by: Michael R

0

Answer 1

Although we don't offer a direct replacement, as Shelby is no longer in business, the Fulton #FTJ120W0301 would be compatible with the snap ring base your Shelby 5776 used. The jack has a 1200 lb capacity and offers 10 inches of lift.…

view full answer...

Answer 2

What we have heard is that the Fulton #FTJ120W0301 does fit the mounting plate of the Shelby Jack 5784.

view full answer...

Answer 3

Shelby has been out of business for a number of years now and so there unfortunately are no replacement parts readily available. You might be able to find something where old parts are regularly sold, but you'll probably have to do a lot of…

view full answer...

Answer 4

I do have a solution for you, however replacement parts for your Shelby 5854A Trailer Jack are no longer available. I recommend simply replacing your Shelby jack with a similar unit like the Fulton Bolt-Thru Swivel Trailer Jack #FXPD15L. This zinc…

view full answer...

Answer 5

Parts are no longer available for the old Fulton Magnum jacks unless it is one of the following jack models: TJ503/C, TJU503, PMJ53, TJ507/C, PMJ75, CS750, GR700/TJ712, XP10/6/W/WC and XP100. Then you would use #F0933302S00. But we do have parts…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Replacement Sidewind Handle and Gear Kit for Bulldog Round Jacks

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching