Recommended Procedure for Cleaning Tree Sap off Truxedo Soft Tonneau Cover

Question

Question:

got some pine tree sap on tonnaeu cover how do i get it off with out damaging cover???

asked by: Anthony P

0

Expert Reply:

My Truxedo representative recommends using hot water, car wash soap and a soft bristle brush to remove that sap. It's going to take some elbow grease, but that should remove it. Once you have the sap removed, Truxedo recommends using their Pro-Tex protectant spray, part # TX1704511 to provide a layer of protection that will prevent sap from sticking next time.

expert reply by: Mike L

0

Answer 1

My Truxedo representative recommends using hot water, car wash soap and a soft bristle brush to remove that sap. It's going to take some elbow grease, but that should remove it. Once you have the sap removed, Truxedo recommends using their…

view full answer...

Answer 2

Although there can be many things that would cause you to read an Overload error code on your P3, I will run through the most common culprits for you that will be pretty easy to check. If you can try the controller out with another trailer, you can…

view full answer...

Answer 3

The first error code, SH, you are seeing on the Prodigy Brake Controller (instructions linked below) means the brake wire sees a short circuit during idle condition. The second code, OL, indicates an overload condition during operation. For the first…

view full answer...

Answer 4

The 89-inch/3500-lb axle kit #e43SR, for example, includes electric drum brake assemblies so it will have wiring in place. Electric brakes are simple to wire; there are only two pigtail leads from each brake and either one can be used for ground or…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Recommended Procedure for Cleaning Tree Sap off Truxedo Soft Tonneau Cover

Product Page this Question was Asked From

Continue Researching