Cargo Carrier and Light Kit Recommendation

Question

Question:

Do you have a light kit that would work for this carrier?

asked by: Jarett P

0

Expert Reply:

The light kit # e98943-44LED will fit your etrailer Carrier part # e98874. I have attached video of them for you.

expert reply by: Jameson C

0

Answer 1

Unfortunately, Rola doesn't make a folding version of the #59502 and an adapter is not an option for it. The etrailer Folding Cargo Carrier, part #e98874 will fit your vehicle if the hitch pin hole to rear of bumper measurement is less than 9-1\2…

view full answer...

Answer 2

I have a solution for your etrailer cargo carrier, but #98174LED is not the correct light. To add LED lights on your carrier you need the Light Kit #e98943-44LED.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The best hitch for a 2024 Subaru Outback is the etrailer item #e25TR. This hitch is custom fit and bolts to your Subaru with included hardware. This is a class III hitch with a 2" receiver, that has a 3,500 lbs towing capacity and a 350 lbs…

view full answer...

Answer 6

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 7

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

I have a set that will work however your 2023 Chevy Suburban's owners manual says not to use tire chains because of clearance issues on the inner part of the tires. You can find this information on page 370. To avoid damaging brake lines and…

view full answer...

Answer 10

When the Curt hitch part #C13420 is installed on a vehicle like your 2020 Kia Telluride the height of the hitch opening is right about the same height as the exhaust. So your best option would be a cargo carrier with a rise built into the shank. The…

view full answer...

Answer 11

Yes, your Champion 200961 will fit the TorkLift Lock and Load SideKick Cargo Tray #TLA7901. The inside dimensions of the tray are 21-1/4" long x 16-1/8" wide x 3-15/16" deep. The 200961 is 17.3" long x 12" wide so it…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Cargo Carrier and Light Kit Recommendation

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching