Installation Bolts for the CE Smith Hanger Bracket part # CE14017G

Question

Question:

What bolt size is used to install the bolt-on spring hangers CE14016G and CE14017G?

asked by: Stephen

1

Helpful Expert Reply:

The mounting holes of the part # CE14017G and # CE140116G that you referenced are 7/16 inches in diameter. You would need to get bolts that would fit those hole sizes. Since applications can vary there isn't a set bolt size you would need. Your best option would be to find a bolt long enough for your application that would fit in the hole.

expert reply by: Jameson C

1

Answer 1

We do have a few hangers with 3 holes in the top, like parts #CE14016G and #CE14017G, but they are for 1-3/4" wide slipper springs. The former is 2-1/4" tall while the latter is 1-3/4" tall. If these match your current hangers then…

view full answer...

Answer 2

I recommend using the 4-Leaf Slipper Spring w/ Flat End for 3,700-lb Trailer Axles - 30" Long Item #SP-040275, for your trailer leaf springs that are 28.5 from center of bolt to center of bolt with 3,000 lbs trailer. You will need a slipper…

view full answer...

Answer 3

The top holes you see in trailer suspension hangers such as Single-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front, 1-1/4" Rear Item #APS3 are for button welds and not bolts so these hangers should not be bolts on. The problem…

view full answer...

Answer 4

The only difference between the Flat and Radius end slipper springs is the shape of the end of the spring with the radius having an arch and the flat being flat as you can see in the included pictures of the Radius End #SP-179275 and Flat End #e29SR.…

view full answer...

Answer 5

The difference is found in the application. The Slipper Spring styles, like part #SP-179275, are intended for use with more heavy duty applications, while the Double Eye styles, like part #e77SR are used to provide a more comfortable ride. The part…

view full answer...

Answer 6

We unfortunately do not have exactly the spring you are looking for. What I recommend is getting the 3-Leaf Slipper Spring w/ Radius End for 1,500-lb Trailer Axles - 24-5/8" Long #SP-178275 and moving your rear hanger forward because you will be…

view full answer...

Answer 7

The top mounting holes on the CE Smith Front Hanger Bracket #CE14016G are as follows: The 2 top holes on the ends are 7/16 inches in diameter The center top hole is 1/2 inch in diameter The lower spring eye holes are 9/16 inch diameter I have…

view full answer...

Answer 8

I have a solution for you, but the leaf springs we sell aren't rated for off-road use. That's why you are snapping springs. Off-road conditions are just too rough for trailer springs designed for on-road use. Instead you would want the…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

You can put a maintenance charge on your trailer battery with the 12 volt accessory circuit of the 7-way. The 1:00 position of your 7-way carries this circuit. You would just need to run a length of 10 gauge wire like part #10-1-1 (sold by the foot),…

view full answer...

Answer 11

To determine the correct springs you will need to know a few variables to ensure that you do not damage your trailer. You have the first variable being the load or as you suggest a 1,000lb raft. Next you need to add the weight of the trailer frame…

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Installation Bolts for the CE Smith Hanger Bracket part # CE14017G

Product Page this Question was Asked From

Continue Researching