How to Shorten Hydraulic Disc Brake Lines

Question

Question:

i need to shorten the hyd steel lines that came with my disc brake kit , what tool will i need and where can i purchase it

asked by: James A

0

Expert Reply:

Thank you for your purchase from etrailer!

The flexible brake lines you selected, Titan # T0777300 and # T0776500, are not designed for cutting. These are offered in the various lengths to allow you to avoid that need and these flex lines are also intended for use near the brake assemblies where their flexibility allows them to handle the motion of the trailer suspension.

If you purchased elsewhere a brake kit with rigid steel lines you will need a flaring tool (which we do not offer) that you should be able to find at your local auto parts store.

expert reply by: Adam R

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the…

view full answer...

Answer 3

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 4

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 10

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 11

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 12

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

How to Shorten Hydraulic Disc Brake Lines

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching