Parts Needed to Upgrade the Dacromet Calipers of # K2HR526D to Stainless Steel Calipers

Question

Question:

I have a set of 12inch Kodiac disc brakes K2HR526D. Im planning on replacing the calipers KDBC225DAC with stainless steel calipers. KDBC225S. Since the original brake kit was designed for regular calipers is there an issue? For instance do I need a stainless steel mounting bracket or stainless hubs?

asked by: Beau M

0

Expert Reply:

All you would need to replace the dacromet calipers of the Disc Brake kit part # K2HR526D that you have on your trailer would be the Kodiak Disc Brake Caliper # KDBC225S that you referenced. This is an identical caliper as what you currently have except it is made of stainless steel.

expert reply by: Jameson C

0

Answer 1

The Kodiak Disc Brake Kit - 12" Hub/Rotor - 6 on 5-1/2 - Dacromet - 5,200 lbs to 6,000 lbs #K2HR526D does come with brake pads. These are high-performance ceramic brake pads. When the time comes to replace them in the future, you will want to…

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 4

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 5

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 6

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Parts Needed to Upgrade the Dacromet Calipers of # K2HR526D to Stainless Steel Calipers

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching