License Plate Bracket for a 1992 Jayco Pop-up Trailer

Question

Question:

I own a 1992 Jayco Camper Pop up Trailer. A License Plate Bracket under the left tail light broke and I lost my license plate. The bracket was a hard rubber mounted underneath the light. I am looking for a replacement of same type or any metal or zinc that will last. Please advise if I can replace that piece or if I need to replace the hold tail light housing.

asked by: Bobby T

0

Expert Reply:

We may not have the exact same license plate bracket as the one you lost on your Jayco trailer. But we do have quite a few that you could likely use.

Bracket # LP15SB is an excellent choice since it is metal and would be more durable and would not cause ground problems (if the tail light grounds through the mounting studs). It mounts on holes that are 2 inches apart on center.

If you happen to need a hole spacing that is 1-3/4 inches apart then you could use # LP20SB.

I have included a couple of pictures showing the key measurements and a link to the right to all of the brackets we carry.

expert reply by: Michael H

0

click to enlarge

Answer 1

The Trailer License Plate Holder with LED Light #328-003-71BE uses non-submersible lights. Although this would not work well on your boat trailer, I have a different solution. I recommend using the LED Trailer License Plate Light #LPL82CBB. This…

view full answer...

Answer 2

For a small lockable storage box for your PWC trailer I would recommend the DeeZee Toolbox part #DZDB-2600. The dimensions of this box are 24" long x 18" wide x 18" tall. Attaching it requires a little bit of creativity, the easiest…

view full answer...

Answer 3

To adjust the hitch latch on your trailer's coupler, you will want to adjust the nut at the bottom of the latch. This nut will be tightened or loosened depending on what you need for your coupler. I have attached a diagram showing you the…

view full answer...

Answer 4

Hi Tracy, We can for sure get you a 3-bike rack for your ebike with a step-thru frame and two regular bikes. This is especially doable because your ebike is on the lighter side at just 40 lbs, and with that in mind what I recommend is a rack from…

view full answer...

Answer 5

The DeeMaxx Disc Brake Kit #DE28YR does not have the E-Z grease fitting, you'd want to take a look at the Kodiak Disc Brakes #KOD69FR instead. This brake assembly is the same thing as #DE28YR but also includes 2 hub-rotor assemblies with…

view full answer...

Answer 6

The RockyMounts HighNoon FC #RKY74MR and MonoRail #RKY10004-10005 are very similar, but do have a few differences. The HighNoon has a 45lb per bike capacity when hauling three bikes or 60lb per bike capacity when hauling only two bikes. The MonoRail…

view full answer...

Answer 7

The Kodiak Disc Brakes #KOD69FR will fit on 5,200lb axles which use the #42 spindle dimensions. This is the most commonly used size but depending on the age of your trailer you may want to inspect your spindle. It will have a grease seal landing…

view full answer...

Answer 8

I do have an option for you but Atwood was bought out and their replacement parts are no longer available, including the repair kit you would need. The best option is to replace that A-frame coupler with a new one that attaches to a 2 inch hitch…

view full answer...

Answer 9

Your Dometic 57915.531 is a 13.5k BTU AC unit which the Advent Air RV AC Unit #ACDOM135 is the same size and is also designed to replace Dometic units.

view full answer...

Answer 10

We do indeed have brackets that would work for the Fulton #F008595-2 fenders, part # PF1135-BKT-2. Each set includes two brackets. I've provided a photo showing how the brackets work.

view full answer...