How to Prevent a 12 Inch Receiver Hitch Extension From Rattling in Receiver

Question

Question:

Im using this to help keep a twelve inch hitch extension from wobbling. Mi first attempt was not successful. Do have any installation information? Thank you

asked by: Eric B

0

Expert Reply:

Adding an extension introduces another component in between the receiver and the ballmount or hitch accessory. Because of this, getting a certain amount of wobble is unavoidable. If you're using the extension for a hitch mounted accessory, you can use an anti-rattle device like part # BX88224.
However, keep in mind that using an extender will lower the tongue weight capacity of your hitch by 50 percent.

If you'll be towing, you'd be better off using a longer ball mount, if the longer ball mounts we offer have a suitable rise/drop for your needs. The # BM20 provides 3/4 inches of rise or 2 inches of drop. The ball mount offers 16 inches of extension between the ball hole and the hitch pin hole. For a larger rise/drop, check out # D-28 which offers 4 inches of rise and 6 inches of drop. Since the ball mount is a single piece, a locking anti-rattle hitch pin like # 63232 would be pretty effective.

expert reply by: Mike L

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

In regards to HappiJac Truck-Mounted Camper Tie-Downs like part #LC182908-182928, the front tie-down installs inside the bed on the front panel directly behind the cab. The rear tie-down then mounts to the bumper. They will not require removal of…

view full answer...

Answer 4

Thanks for the pictures but no, the EX2700 tonneau cover that the #EX1700 fits is for a 2004-15 Nissan Titan 6' 7" Bed. The one previously mentioned #EX1770 is for your truck, so it'd for sure work if you have the 2770…

view full answer...

Answer 5

Great news! The Draw-Tite Ultra Frame Trailer Hitch Receiver #41929 actually sits below the OEM receiver on your 2008 Dodge Ram 1500 so you don't have to remove anything for this installation! I have attached a clip from the installation…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 7

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The Tow Defender #RM-4700 you found is really our best option to protect the front of your 2024 Chevrolet Trax. This screen helps to deflect any road debris back down to the ground to keep it traveling under your Trax. This particular cover is…

view full answer...

Answer 11

Just looking at your Tern HSD bike with fenders, I'm going to say no the Saris MHS Bike Rack for 1 Bike #SAR23MR is not going to work. I did some research and it looks like a lot of Tern owner's went with the Hollywood Racks Sport…

view full answer...