Replacement Lens for the Taillight Assembly part # A39RB

Question

Question:

I have included a picture of the complete light assembly ST37RB. Circled in yellow is a 90 deg. tab at one end of the lense that does not appear in the discriptive photos of the replacement lens. I need a replacement lens that has the tab. Also I need a license plate bracket to fit behind an ST37RB. Recommendations? Thank you. Best regards,

asked by: Michael W

0

Expert Reply:

For the taillight assembly part # ST37RB that you referenced there are 2 lens. One of them is the part # A39RB that you referenced that covers the front of the assembly.

For the side piece that you referenced you would want the part # A37RB.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Thanks for the picture of your trailer light! From that I can tell you have a light like part #ST37RB and the correct replacement lens is the #A37RB.

view full answer...

Answer 2

The lights you have on your trailer are #ST37RB and #ST36RB. The replacement lenses are #A39RB for the front lens and #A37RB for the side marker.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Lens for the Taillight Assembly part # A39RB

Products Referenced in This Question

Continue Researching